JXP-01LMAB1 JDSU [JDS Uniphase Corporation], JXP-01LMAB1 Datasheet
JXP-01LMAB1
Related parts for JXP-01LMAB1
JXP-01LMAB1 Summary of contents
Page 1
... Multiprotocol XFP Optical Transceiver—1310 nm for Reach JXP Series Applications • Wide area network (WAN) • Local area network (LAN) • Storage area network (SAN) • SONET OC-192 applications • SDH STM-64 applications • Ethernet switches and applications • Fibre Channel switches and applications Compliance • ...
Page 2
... SONET/SDH Ethernet Fibre Channel and corresponding for- ward error correction (FEC) rates specifications. Closed-loop control of the trans- mitted laser power and modulation swing over temperature and voltage variations is provided. The laser is coupled to single-mode optical fiber through an industry- standard LC optical connector. ...
Page 3
... The receiver converts incoming DC balanced serial NRZ optical data from line rate of 9.95 to 11.35 Gbps into serial XFI electrical data. Light is coupled to a PIN photodetector from single-mode optical fiber through an industry-standard LC optical connector. The electrical current from the PIN photodetector is converted to a voltage in a high-gain transimpedance amplifier. ...
Page 4
MUlTIPROTOCO l XFP O PTICA l TRANSCEI vER —1310 NM FOR REACH low-speed Signaling Low-speed signaling is based on low voltage TTL (LVTTL) operating at a nominal voltage of 3.3 V. SCL/SDA: Two-wire serial interface ...
Page 5
System Loopback Figure 2 Application schematics for the 10 Gbps 1310 nm XFP optical transceiver MUlTIPROTOCO l XFP O PTICA l TRANSCEI vER —1310 NM FOR REACH POWER INPUT 2 TD +/- XFP ...
Page 6
Pin Function Definitions Figure 3 MUlTIPROTOCOl XFP OPTICAl TRANSCEIvER —1310 NM FOR REACH GND 16 GND RX_LOS 17 RD- Mod_NR 18 RD+ Mod_ASB 19 GND SDA 20 VCC2 SCL 21 P_Down/RST VCC3 22 VCC2 ...
Page 7
Table 1 XFP Optical Transceiver Pin Descriptions Pin Number Type Name 1 GND 2 VEE5 3 LVTTL-I Mod_Desel 4 LVTTL-O Interrupt 5 LVTTL-I TX_DIS 6 VCC5 7 GND 8 VCC3 9 VCC3 10 LVTTL-I SCL 11 LVTTL-I/O SDA 12 ...
Page 8
... Absolute maximum ratings represent the damage threshold of the device. Damage may occur if the device is operated above the limits stated here except for brief excursions. Performance is not guaranteed and reliability is not implied for operation at any condition outside the recommended operating limits. 3.4 Operating Conditions Part Number SONET/SDH and FEC (9.95 to 11.35 Gbps) JXP-01LMAB1 X JXP-01LMAC1 X JXP-01LEAB1 JXP-01LGAB1 Note: Performance is not guaranteed and reliability is not implied for operation at any condition outside the recommended operating limits ...
Page 9
Electrical Characteristics Parameter Symbol Minimum Supply currents and voltages Voltage3 V 3.13 CC3 Voltage5 V 4.75 CC5 Voltage2 V CC2 Supply current3 I CC3 Supply current5 I CC5 Supply current2 I CC2 Power dissipation Pwr Low-speed control and ...
Page 10
Jitter Specifications Parameter Symbol Transmitter electrical input jitter from host at B (detailed specification in XFP MSA INF8077i Rev. 4.5) Total non-EQJ jitter Total jitter TJ Eye mask X1 Eye mask Y1 Eye mask Y2 Receiver electrical output ...
Page 11
XFP MSA Reserved Serial ID For Future Data Diagnostic 223 Functions 224- Vendor Specific ID Data 255 255 Table 00H Table 01H Figure 5 MUlTIPROTOCOl XFP OPTICAl TRANSCEIvER —1310 NM FOR REACH ...
Page 12
Optical Transmitter Characteristics Parameter Center wavelength -20 dB spectral width Sidemode suppression ratio Relative intensity noise Average optical power (SONET/SDH) (EOL) Extinction ratio 1 (SONET/SDH) Chromatic dispersion penalty Optical path penalty Return loss tolerance Datacom module optical transmitter ...
Page 13
Table 2 Regulatory Compliance Feature Component safety RoHS-compliance Laser eye safety Electromagnetic Compatibility Electromagnetic emissions Electromagnetic immunity ESD immunity Radiated immunity MUlTIPROTOCOl XFP OPTICAl TRANSCEIvER —1310 NM FOR REACH 3.11 Regulatory Compliance The 10 Gbps ...
Page 14
Module Outline Figure 6 MUlTIPROTOCOl XFP OPTICAl TRANSCEIvER —1310 NM FOR REACH Belly-to-Belly Mounting Recommendation 3.14 Connectors Fiber The XFP module has a duplex LC receptacle connector. Electrical The electrical connector is the 30-way, ...
Page 15
... Note recommended that the connector plug remain on whenever the trans- ceiver optical fiber connector is not inserted. Recommended cleaning and degreasing chemicals JDSU recommends the use of methyl, isopropyl and isobutyl alcohols for cleaning. ...
Page 16
... Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at customer.service@jdsu.com. Sample: JXP-01lMAB1 Product Code Description JXP-01LMAB1 Multiprotocol, OC-192 SR-1, 10 GbE/FC LR/LW, 1310 nm, industrial temperature range 10 Gbps XFP optical transceiver ...