JXP-01LMAB1 JDSU [JDS Uniphase Corporation], JXP-01LMAB1 Datasheet - Page 10

• Manufacturer Part Number: JXP-01LMAB1
• Description: Multiprotocol XFP Optical Transceiver-1310 nm for up to 10 km Reach
• Manufacturer: JDSU [JDS Uniphase Corporation]

10
3.6
Parameter
Transmitter electrical input jitter from host at B (detailed specification in XFP MSA INF8077i Rev. 4.5)
Total non-EQJ jitter
Total jitter
Eye mask
Eye mask
Eye mask
Receiver electrical output jitter to host at C (detailed specification in XFP MSA INF8077i Rev. 4.5)
Deterministic jitter
Total jitter
Eye mask
Eye mask
Eye mask
Eye mask
Telecom module optical transmitter and receiver jitter (detailed specification in XFP MSA INF8077i Rev. 4.5 and GR-253-CORE
Issue 4-2005)
Jitter transfer bandwidth BW
Jitter peaking
Transmitter jitter generation
Datacom module optical transmitter and receiver jitter (detailed specification in XFP MSA INF8077i Rev. 4.5)
Jitter transfer bandwidth BW
Jitter peaking
1. Specifications are applicable to all Part Numbers listed in Section 3.4.
2. Specifications are applicable to SONET / SDH compliant Part Numbers listed in Section 3.4 only.
3.7
Parameter
TX_DIS assert time
TX_DIS negate time
Time to initialize
Interrupt assert delay
Interrupt negate delay
P_Down/RST assert delay
Mod_NR assert delay
Mod_NR negate delay
P-Down reset time
RX_LOS assert delay
RX_LOS negate delay
Note:
Two-wire serial bus timing is described in Chapter 4 of XFP MSA INF8077i Rev. 4.5.
Jitter Specifications
Timing Requirement of Control and Status I/O
2
Symbol
TJ
X1
Y1
Y2
DJ
TJ
X1
X2
Y1
Y2
Symbol
t_off
t_on
t_init
Interrupt_on
Interrupt_off
P_Down/RST_on
Mod_NR_on
Mod_NR_off
t_loss_on
t_loss_off
Min
60
170
Min
10
Max
10
2
300
200
500
100
1
1
100
100
MUlTIPROTOCOl XFP OPTICAl TRANSCEIvER
—1310 NM FOR UP TO 10 KM REACH
Max
0.41
0.61
0.305
410
0.18
0.34
0.17
0.42
425
8
1
0.3
0.1
8
1
Unit
µsec
msec
msec
msec
µsec
µsec
msec
msec
µsec
µsec
µsec
10% of nominal
Falling edge of TX_DIS to rise of output signal above
90% of nominal
From power on or from falling edge of P_Down/RST
From occurrence of the condition triggering Interrupt.
From clear on read Interrupt flags
From power down initiation
From occurrence of fault to assertion of Mod_NR
From clearance of signal to negation of Mod_NR
Min. length of P-Down assert to initiate reset
From Occurrence of loss of signal to assertion of RX_LOS
From Occurrence of return of signal to negation of RX_LOS
Notes
Rising edge of TX_DIS to fall of output signal below
Unit
UI(p-p)
UI(p-p)
UI
mV
mV
UI(p-p)
UI(p-p)
UI
UI
mV
mV
MHz
dB
UI
UI
MHz
dB
pp
pp
Notes
Total jitter less ISI
Mask coordinate X1=0.205 if total non-DDJ
is measured
50 mV is allocated for multiple reflections
Includes jitter transferred from the optical receiver
during any valid operational input condition.
Includes jitter transferred from the optical receiver
during any valid operational input condition.
PRBS 2
SDH-64 Sinusoidal Jitter Tolerance Mask
Frequency >120 KHz
20 KHz to 80 MHz
4 MHz to 80 MHz
PRBS 2
detailed in IEEE 802.3-2005 Clause 52
Frequency >50 KHz
31
31
1
-1, OC-192 /
-1, Data or scrambled 64 B/66 B as
1
1