SSTU32865ET/G,518 NXP Semiconductors, SSTU32865ET/G,518 Datasheet - Page 10

• Manufacturer Part Number: SSTU32865ET/G,518
• Description: IC REG BUFFER 28BIT 160-TFBGA
• Manufacturer: NXP Semiconductors

Specifications of SSTU32865ET/G,518

• Logic Type: 1:2 Registered Buffer with Parity
• Package / Case: 160-TFBGA
• Supply Voltage: 1.7 V ~ 1.9 V
• Number Of Bits: 28
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Logic Family: SSTU
• Number Of Circuits: 1
• Maximum Clock Frequency: 450 MHz
• Propagation Delay Time: 1.8 ns
• High Level Output Current: - 8 mA
• Low Level Output Current: 8 mA
• Supply Voltage (max): 1.9 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Supply Voltage (min): 1.7 V
• Function: Registered Buffer
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935275433518; SSTU32865ET/G-T; SSTU32865ET/G-T

Philips Semiconductors
9397 750 13799
Product data sheet
7.3.1 Chip Select (CS) gating of key inputs (DCS0, DCS1, CSGATEEN)
7.3.2 Parity error checking and reporting
7.3.3 Reset (RESET)
7.3.4 Power-up sequence
7.3 Functional differences to SSTU32864
The SSTU32865 for its basic register functionality, signal definition and performance is
based upon the industry-standard SSTU32864, but provides key operational features
which differ (at least in part) from the industry-standard register in the following aspects:
As a means to reduce device power, the internal latches will only be updated when one or
both of the CS inputs are active (LOW) and CSGATEEN HIGH at the rising edge of the
clock. The 22 ‘Chip-Select-gated’ input signals associated with this function include
addresses (ADDR0 to ADDR15, BA0 to BA2), and RAS, CAS, WE, with the remaining
signals (CS, CKE, ODT) continuously re-driven at the rising edge of every clock as they
are independent of CS. The CS gating function can be disabled by tying CSGATEEN
LOW, enabling all internal latches to be updated on every rising edge of the clock.
Table 5:
The SSTU32865 incorporates a parity function, whereby the signal received on input pin
PARIN is received as parity to the register, one clock cycle later than the CS-gated inputs.
The received parity bit is then compared to the parity calculated across these same inputs
by the register parity logic to verify that the information has not been corrupted. The 22
CS-gated input signals will be latched and re-driven on the first clock, and any error will be
reported one clock cycle later via the PTYERR output pin (driven LOW for two consecutive
clock cycles). PTYERR is an open-drain output, allowing multiple modules to share a
common signal pin for reporting the occurrence of a parity error during a valid command
cycle (coincident with the re-driven signals). This output is driven LOW for two consecutive
clock cycles to allow the memory controller sufficient time to sense and capture the error
even. A LOW state on PTYERR indicates that a parity error has occurred.
Similar to the RESET pin on the industry-standard SSTU32864, this pin is used to clear all
internal latches and all outputs will be driven LOW quickly except the PTYERR output,
which will be floated (and will normally default HIGH by their external pull-up).
The reset function for the SSTU32865 is similar to that of the SSTU32864 except that the
PTYERR signal is also cleared and will be held clear (HIGH) for three consecutive clock
cycles.
Mode
Gating
Non-gating
Chip Select gating mode
Signal name
CSGATEEN
HIGH
CSGATEEN
LOW
Rev. 02 — 28 September 2004
Description
Registers only re-drive signals to the DRAMs when
Chip Select inputs are LOW.
Registers always re-drive signals on every clock cycle,
independent of the state of the Chip Select inputs.
1.8 V DDR registered buffer with parity
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
SSTU32865
10 of 29