A3980KLP Allegro Microsystems Inc, A3980KLP Datasheet - Page 15

• Manufacturer Part Number: A3980KLP
• Description: IC DRIVER MICROSTEPPING 28-TSSOP
• Manufacturer: Allegro Microsystems Inc

Specifications of A3980KLP

• Applications: Stepper Motor Driver
• Number Of Outputs: 1
• Current - Output: ± 1A
• Voltage - Load: 7 V ~ 50 V
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP Exposed Pad, 28-eTSSOP, 28-HTSSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

A3980
The total dissipation for each of the four decay modes is the
average power for the current ramp and the current decay
portions of the PWM cycle.
For slow decay, the current is rising for approximately 20%
of the cycle and decaying for approximately 80%. For fast
decay, the ratio is approximately 50% for each. Note that
these are approximate fi gures, and they vary slightly depend-
ing on the motor characteristics and the use of synchronous
rectifi cation.
The power dissipation, P
calculated as shown in the following formulas.
Synchronous slow decay mode:
Allowable Package Power Dissipation
5
4
3
2
1
0
P
1
“High-K” 4-layer PCB.
2
with 3 in.
TOT
25
R
R
θJA
θJA
= [0.2
at 28ºC/ W measured on a JEDEC-standard
at 38ºC/ W measured on a typical 2-sided PCB
2
2
(1935 mm
R
×
50
θJA
I
2
P
TOT
(R
= 38ºC/W
Ambient Temperature (°C)
DSONH
= (0.2
2
) copper ground area.
75
TOT
+ R
, in each decay mode can be
×
1
DSONL
R
P
D
θJA
) + (0.8
100
)] + [0.8
= 28ºC/W
×
×
125
P
SS
I
2
)
Automotive DMOS Microstepping Driver
(2
×
R
150
DSONL
)]
Non-synchronous slow decay mode:
Synchronous fast decay mode:
Non-synchronous fast decay mode:
An approximation of the total dissipation can be calculated
by summing the total power dissipated in both full-bridges
and adding the control circuit power due to V
V
ture can then be compared to the allowable power dissipation,
shown in the Allowable Package Power Dissipation chart.
For critical applications, where the fi rst order power estimate
is close to the allowable dissipation, the power calculation
should take several other parameters into account including:
motor parameters, dead time, and switching losses in the
controller.
Layout. The printed circuit board should use a heavy
ground plane. For optimum electrical and thermal perfor-
mance, the A3980 should be soldered directly onto the board.
The load supply terminal, V
an electrolytic capacitor (> 47 μF is recommended), placed
as close to the A3980 as possible. To avoid problems due to
capacitive coupling of the high dv/dt switching transients,
route the full-bridge output traces away from the sensitive
logic input traces. Always drive the logic inputs with a low
source impedance to increase noise immunity.
Grounding. A star ground system located close to the
A3980 is recommended. On the 28-lead TSSOP package, the
analog ground (lead 7) and the power ground (lead 21) must
be connected together externally. The copper ground plane
located under the exposed thermal pad is typically used as
the star ground point.
DD
P
P
×
TOT
TOT
I
DD
= [0.2
= [0.5
. The total power at the required ambient tempera-
×
×
I
2
P
P
(R
I
P
P
TOT
TOT
2
TOT
TOT
DSONH
(R
= (0.5
= (0.5
DSONH
= (0.2
= I
+ R
2
(R
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
DSONL
×
BB
×
×
+ R
DSONH
, should be decoupled with
P
P
P
D
D
DSONL
D
)] + {0.8
) + (0.8
) + (0.5
) + (0.5
with Translator
+ R
)] + (0.5
DSONL
×
×
×
×
[I
P
2
P
P
)
R
NS
NF
BB
SF
×
DSONL
)
)
)
I
×
2
×
+ (I
I
BB
R
×
DSONL
and
V
F
)]}
)
15