HFBR-2505A Avago Technologies US Inc., HFBR-2505A Datasheet
HFBR-2505A
Specifications of HFBR-2505A
Related parts for HFBR-2505A
HFBR-2505A Summary of contents
Page 1
... MBd and data transfer between numerical controls and drives via fiber-optic rings, with voltage isolation and noise immunity. The HFBR-1505A and HFBR-2505A products comply with SERCOS specifications for optical characteristics and connector style, and have guaranteed performance MBd. (Typically the ...
Page 2
... HFBR-1515B/2515B Pulse Width Distortion with HFBR-1505C/2505C Notes: 1. With recommended Tx and Rx circuits (60 mA nominal drive current). 2. POF HFBR-Exxyyy 0.23 dB/m worst case attentuation. ® 3. HCS 10 dB/km worst case attenuation. 4. Including optical safety margin accounting for link service lifetime. 5. Including optical safety margin accounting for link service lifetime. ...
Page 3
... Rise Time (10% to 90%) Fall Time (90% to 10%) EYE SAFETY: The HFBR-15x5x is a Class 1 LED Product and eye safe when used within the data sheet limits and under normal operating conditions. This includes all reasonably foreseeable single fault conditions per IEC60825-1 and amendments. ...
Page 4
... HFBR-1505A P T SERCOS HFBR-1515B PROFIBUS HFBR-1505C INTERBUS-S Notes: 1. Typical data at 25˚C. 2. Optical power measured at the end of 0.5 meters diameter plastic optical fiber with a large area detector. 3. Minimum and maximum values for P over temperature are based on a fixed drive current. The recommended drive circuit has temperature ...
Page 5
... 1 0.8 0.7 -40 - TEMPERATURE – °C Figure 4. Typical normalized optical power vs. temperature (in recommended drive circuit). Recommended Drive Circuit for HFBR-x505A/x515B TTL COMPATIBLE TRANSMITTER + µ 0.1 µ DS75451 1 2 TTL INPUT 82 Figure 6. Recommended transmitter and receiver drive circuit ( 5.25 V ...
Page 6
... PWD for arbitrary data patterns. The receiver output is a “push–pull” stage compatible with TTL and CMOS logic. The receiver housing is a dark grey, conductive plastic. The HFBR-2505A is compatible with SMA connectors, while the HFBR-2515B mates with ® ST connectors ...
Page 7
-40 - 100 TEMPERATURE – °C Figure 7. Typical POF receiver overdrive P ...
Page 8
... Pins 1 and 4 are electrically connected to the conductive housing and are also used for mounting and retaining purposes required that pin 1 and 4 be connected to ground to maintain conductive housing shield effectiveness. 8 pin 5. The receiver housing is a dark gray conductive plastic and the optical port is compatible with SMA connectors. The speci-fied signal rate of HFBR-2505C is 2 MBd. Symbol Min. T – – ...
Page 9
... CCH I 6.2 10 CCL 0.5 R 680 1000 1700 L / – HFBR-1505C 82 Units Conditions dBm V = 0.5 V Notes POF 200 m HCS dBm V = 5.25 V Note 250 Note mA, Note R(L)MIN 5.25 V, Note 5.25 V Note -12.5 dBm R mm TTL COMPATIBLE RECEIVER 0.1 µ HFBR-2505C TTL OUTPUT Ref ...
Page 10
... Mechanical Dimensions HFBR-X515X 12.5 (0.49) DATE CODE 1.3 (0.05) 1.3 (0.050) 1.0 3.6 (0.04) (0.140) HFBR-X505X 12.5 (0.49) DATE CODE 1.3 (0.05) 1.3 (0.050) 1.0 3.6 (0.04) (0.140) 10 21.2 (0.83) 7.0 (0.28) PART NUMBER 7.6 4.8 (0.30) (0.19) 1.5 (0.06) 3.8 (0 ...
Page 11
For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright © ...