LTM4609MPV#PBF Linear Technology, LTM4609MPV#PBF Datasheet - Page 10

• Manufacturer Part Number: LTM4609MPV#PBF
• Description: IC UMODULE BUCK-BOOST 141-LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM4609MPV#PBF

• Design Resources: LTM4609 Spice Model
• Output: 0.8 ~ 34 V
• Number Of Outputs: 1
• Power (watts): 136W
• Mounting Type: Surface Mount
• Voltage - Input: 4.5 ~ 36 V
• Package / Case: 141-LGA
• 1st Output: 0.8 ~ 34 VDC @ 4A
• Size / Dimension: 0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
• Power (watts) - Rated: 136W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 98%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -

APPLICATIONS INFORMATION
LTM4609
locked loop comprised of an internal voltage controlled
oscillator and a phase detector. This allows turning on the
internal top MOSFET for locking to the rising edge of the
external clock. A pulse detection circuit is used to detect
a clock on the PLLIN pin to turn on the phase-lock loop.
The input pulse width of the clock has to be at least 400ns,
and 2V in amplitude. The synchronized frequency ranges
from 200kHz to 400kHz, corresponding to a DC voltage
input from 0V to 2.4V at PLLFLTR. During the start-up of
the regulator, the phase-lock loop function is disabled.
Low Current Operation
To improve effi ciency at low output current operation,
LTM4609 provides three modes for both buck and boost
operations by accepting a logic input on the FCB pin. Table
2 shows the different operation modes.
Table 2. Different Operating Modes (V
When the FCB pin voltage is lower than 0.8V, the controller
behaves as a continuous, PWM current mode synchronous
switching regulator. When the FCB pin voltage is below
V
the controller enters Burst Mode operation in boost opera-
tion or enters skip-cycle mode in buck operation. During
boost operation, Burst Mode operation is activated if the
10
INTVCC
V
0V to 0.75V
INTVCC
0.85V to
FCB PIN
>5.3V
– 1V, but greater than 0.85V, where V
– 1V
Figure 2. Frequency vs PLLFLTR Pin Voltage
450
400
350
300
250
200
150
100
50
0
0
DCM with Constant Freq
Force Continuous Mode
0.5
Skip-Cycle Mode
PLLFLTR PIN VOLTAGE (V)
BUCK
1.0
1.5
INTVCC
2.0
DCM with Constant Freq
Force Continuous Mode
Burst Mode Operation
= 6V)
4609 F02
2.5
BOOST
INTVCC
is 6V,
load current is lower than the preset minimum output
current level. The MOSFETs will turn on for several cycles,
followed by a variable “sleep” interval depending upon the
load current. During buck operation, skip-cycle mode sets
a minimum positive inductor current level. In this mode,
some cycles will be skipped when the output load current
drops below 1% of the maximum designed load in order
to maintain the output voltage.
When the FCB pin voltage is tied to the INTV
controller enters constant frequency discontinuous current
mode (DCM). For boost operation, if the output voltage is
high enough, the controller can enter the continuous current
buck mode for one cycle to discharge inductor current. In
the following cycle, the controller will resume DCM boost
operation. For buck operation, constant frequency discon-
tinuous current mode is turned on if the preset minimum
negative inductor current level is reached. At very light
loads, this constant frequency operation is not as effi cient
as Burst Mode operation or skip-cycle, but does provide
low noise, constant frequency operation.
Input Capacitors
In boost mode, since the input current is continuous, only
minimum input capacitors are required. However, the input
current is discontinuous in buck mode. So the selection
of input capacitor C
input square wave current.
For a buck converter, the switching duty-cycle can be
estimated as:
Without considering the inductor current ripple, the RMS
current of the input capacitor can be estimated as:
In the above equation, η is the estimated effi ciency of the
power module. C
aluminum capacitor, OS-CON capacitor or high volume
ceramic capacitors. Note the capacitor ripple current
ratings are often based on temperature and hours of life.
I
D =
CIN(RMS)
V
V
OUT
IN
=
I
OUT(MAX)
IN
η
IN
can be a switcher-rated electrolytic
is driven by the need of fi ltering the
• D • (1− D)
CC
pin, the
4609fb