ISL28476EVAL1Z Intersil, ISL28476EVAL1Z Datasheet
ISL28476EVAL1Z
Specifications of ISL28476EVAL1Z
Related parts for ISL28476EVAL1Z
ISL28476EVAL1Z Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006, 2007, 2009. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ...
Page 2
Pinouts ISL28176 (8 LD SOIC) TOP VIEW NC 1 IN- IN+ ISL28276 (8 LD SOIC) TOP VIEW OUT_A 1 IN-_A 2 IN+ ISL28176, ISL28276, ISL28476 ...
Page 3
... Thermal Resistance (Typical, Note SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . 16 Ld QSOP Package . . . . . . . . . . . . . . . . . . . . . . . Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . .Indefinite Ambient Operating Temperature Range . . . . . . . . .-40°C to +125°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp = 2.5V Open +25° ...
Page 4
Electrical Specifications 0V,V Boldface limits apply over the operating temperature range, -40°C to +125°C, temperature data established by characterization. (Continued) PARAMETER DESCRIPTION A Large Signal Voltage Gain VOL V Maximum Output Voltage Swing OUT ISL28176 ...
Page 5
Electrical Specifications 0V,V Boldface limits apply over the operating temperature range, -40°C to +125°C, temperature data established by characterization. (Continued) PARAMETER DESCRIPTION I EN Pin Input Low Current ENL AC SPECIFICATONS GBW Gain Bandwidth Product ...
Page 6
Typical Performance Curves 10k 8.3pF + 10mV OUT P-P -9 ...
Page 7
Typical Performance Curves 120 110 100 PSRR + PSRR - ±2. SOURCE P 100kΩ ...
Page 8
Typical Performance Curves 2 OPEN L 1 8.3pF 10 10k 1000 V 0.5 0 -0.5 -1.0 -1.5 -2 ...
Page 9
Typical Performance Curves EN INPUT 0 V OUT 0 10µs/DIV FIGURE 19. ISL28276 ENABLE TO OUTPUT DELAY TIME 100 -20 - OPEN - 100k 100 ...
Page 10
Typical Performance Curves 320 N = 1000 300 MAX 280 MEDIAN 260 240 MIN 220 200 -40 - TEMPERATURE (°C) FIGURE 25. ISL28476 SUPPLY CURRENT vs TEMPERATURE ±2.5V ENABLED ...
Page 11
Typical Performance Curves 200 N = 1000 150 100 MAX 50 0 -50 MIN -100 -150 -200 -40 - TEMPERATURE (°C) FIGURE 31. ISL28476 V vs TEMPERATURE ±2. 2.5 ...
Page 12
Typical Performance Curves 2 2.0 1.5 MAX 1.0 MEDIAN 0.5 0 MIN -0.5 -40 - TEMPERATURE (°C) FIGURE 37. ISL28176 I (-) vs TEMPERATURE V BIAS 2 1000 2.0 MAX 1.5 ...
Page 13
Typical Performance Curves 900 800 MAX 700 600 MEDIAN 500 400 MIN 300 200 100 0 -40 - TEMPERATURE (°C) FIGURE 43. ISL28176 100k, V VOL L 125 n ...
Page 14
Typical Performance Curves 4. 4.90 MAX 4.89 4.88 MEDIAN 4.87 4.86 MIN 4.85 4.84 4.83 4.82 -40 - TEMPERATURE (°C) FIGURE 49. ISL28176 V HIGH vs TEMPERATURE, OUT ±2.5V, ...
Page 15
Typical Performance Curves 0. 0.21 0.19 MAX 0.17 0.15 0.13 MIN 0.11 0.09 -40 - TEMPERATURE (°C) FIGURE 55. ISL28176 + SLEW RATE vs TEMPERATURE ±1.5V OUT V ...
Page 16
Pin Descriptions (Continued) ISL28176 ISL28276 ISL28276 (8 LD SOIC SOIC) (16 LD QSOP IN- IN+ V- CIRCUIT 1 Applications Information Introduction The ISL28176, ISL28276 and ISL28476 are single, dual and quad BiCMOS ...
Page 17
Enable/Disable Feature The ISL28276 (QSOP package only) offers two EN pins (EN_A and EN_B) which disable the op amp when pulled least 2.0V. In the disabled state (output in a high impedance state), the part consumes typically ...
Page 18
Small Outline Package Family (SO PIN #1 I.D. MARK 0.010 SEATING PLANE 0.004 C 0.010 MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) SYMBOL SO-8 SO-14 ...
Page 19
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...