ISL28476EVAL1Z Intersil, ISL28476EVAL1Z Datasheet - Page 16

• Manufacturer Part Number: ISL28476EVAL1Z
• Description: EVALUATION BOARD FOR ISL28476
• Manufacturer: Intersil

Specifications of ISL28476EVAL1Z

• Channels Per Ic: 4 - Quad
• Amplifier Type: General Purpose
• Output Type: Single-Ended, Rail-to-Rail
• Slew Rate: 0.17 V/µs
• Current - Output / Channel: 31mA
• Operating Temperature: -40°C ~ 125°C
• Current - Supply (main Ic): 240µA
• Voltage - Supply, Single/dual (±): 2.4 V ~ 5 V, ±1.2 V ~ 2.5 V
• Board Type: Fully Populated
• Utilized Ic / Part: ISL28476
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -

Pin Descriptions
Applications Information
Introduction
The ISL28176, ISL28276 and ISL28476 are single, dual and
quad BiCMOS rail-to-rail input, output (RRIO) micropower
precision operational amplifiers. These devices are designed
to operate from a single supply (2.4V to 5.0V) or dual
supplies (±1.2V to ±2.5V) while drawing only 120µA
(ISL28276) of supply current. This combination of low power
and precision performance makes these devices suitable for
solar and battery power applications.
Rail-to-Rail Input
Many rail-to-rail input stages use two differential input pairs, a
long-tail PNP (or PFET) and an NPN (or NFET). Severe
penalties have to be paid for this circuit topology. As the input
signal moves from one supply rail to another, the operational
amplifier switches from one input pair to the other causing
drastic changes in input offset voltage and an undesired
change in magnitude and polarity of input offset current.
The devices achieve rail-to-rail input without sacrificing
important precision specifications and degrading distortion
performance. The devices’ input offset voltage exhibits a
smooth behavior throughout the entire common-mode input
range. The input bias current versus the common-mode
voltage range gives us an undistorted behavior from typically
down to the negative rail to 10% higher than the V
higher than V
(8 LD SOIC)
ISL28176
4
IN-
(8 LD SOIC)
+
ISL28276
CIRCUIT 1
when V
4
+
equals 5V).
(Continued)
(16 LD QSOP)
V+
V-
ISL28276
16
IN+
11
7
6
LOGIC
PIN
(16 LD QSOP)
ISL28176, ISL28276, ISL28476
ISL28476
13
14
15
16
+
CIRCUIT 2
rail (0.5V
OUT_D
NAME
IN+_D
IN-_D
EN_A
EN_B
PIN
V-
V+
V-
EQUIVALENT
CIRCUIT
Circuit 4
Circuit 1
Circuit 1
Circuit 3
Circuit 2
Circuit 2
Input Protection
All input terminals have internal ESD protection diodes to the
positive and negative supply rails, limiting the input voltage
to within one diode beyond the supply rails. Both parts have
additional back-to-back diodes across the input terminals. If
overdriving the inputs is necessary, the external input current
must never exceed 5mA. External series resistors may be
used as an external protection to limit excessive external
voltage and current from damaging the inputs.
Input Bias Current Compensation
The devices contain an input bias cancellation circuit which
reduces the bias currents down to a typical of 500pA while
maintaining an excellent bandwidth for a micro-power
operational amplifier. The input stage transistors are still
biased with adequate current for speed but the canceling
circuit sinks most of the base current, leaving a small fraction
as input bias current.
Rail-to-Rail Output
A pair of complementary MOSFET devices are used to
achieve the rail-to-rail output swing. The NMOS sinks
current to swing the output in the negative direction. The
PMOS sources current to swing the output in the positive
direction. Both parts, with a 100kΩ load, will typically swing to
within 4mV of the positive supply rail and within 3mV of the
negative supply rail.
CIRCUIT 3
Negative power supply
Amplifier D non-inverting input
Amplifier D inverting input
Amplifier D output
Amplifier A enable pin internal pull-down; Logic “1”
selects the disabled state; Logic “0” selects the enabled
state.
Amplifier B enable pin with internal pull-down; Logic “1”
selects the disabled state; Logic “0” selects the enabled
state.
V-
OUT
V+
DESCRIPTION
V+
V-
CIRCUIT 4
CAPACITIVELY
COUPLED
ESD CLAMP
June 23, 2009
FN6301.4