ATAVRTS2080A Atmel, ATAVRTS2080A Datasheet - Page 123

• Manufacturer Part Number: ATAVRTS2080A
• Description: KIT QTOUCH W/SW ATMEGA88
• Manufacturer: Atmel
• Series: QTouch™r

Specifications of ATAVRTS2080A

• Sensor Type: Touch, Capacitive
• Sensing Range: 1 Rotor, 1 Slider, and 2 Buttons/Keys
• Interface: Application Programming Interface (API)
• Voltage - Supply: 1.8 V ~ 5.5 V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: ATmega88
• Tool Type: Development Kit
• Cpu Core: AVR 8 / 32
• Data Bus Width: 8 bit
• Core Architecture: AVR
• Silicon Manufacturer: Atmel
• Silicon Core Number: ATmega88, ATmega88A
• Silicon Family Name: AVR
• Kit Contents: Board, CD
• Development Tool Type: Hardware / Software - Eval/Demo Board
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Sensitivity: -
• Lead Free Status / Rohs Status: Details

6.3.8.6
The touch_qt_sensor_disable and touch_qt_sensor_reenable API can be used for Disabling and
Re-enabling of QTouch Group A and Group B Sensors. In order to Disable or re-enable a
sensor, the API must be called with the corresponding sensor_id. Disabling a Sensor disables
the measurement process on all the Touch Channels corresponding to Sensor.
When a QTouch Sensor is Disabled or re-enabled, it is mandatory to force Calibration on all
Sensors. The Calibration of all Sensors is done using the touch_qt_sensors_calibrate API.
6.3.9
6.3.9.1
The Autonomous QTouch Sensor pin selection is similar to selection of pin for QTouch Group A/B
as indicated in
SNSK16 can be chosen to function as an Autonomous QTouch sensor.
6.3.9.2
The Autonomous QTouch Sensor Sensor schematic is similar QTouch schematic as indicated in
Section
6.3.9.3
The clock for the CAT module, CLK_CAT, is generated by the Power Manager (PM). This clock is
turned on by default, and can be enabled and disabled in the PM. The user must ensure that
CLK_CAT is enabled before initializing the QTouch Library for Autonomous QTouch.
For the Autonomous QTouch Sensor, the complete detection algorithm is implemented within the
CAT module. This allows detection of proximity or touch without CPU intervention. Since the
Autonomous QTouch Sensor operates without software interaction, this Sensor can be used to
wakeup from sleep modes when activated. The Autonomous QTouch Status change interrupt
can be used to wakeup from any of the Sleep modes shown in the Table. The ‘Static’ Sleep
mode being the deepest possible Sleep mode from which a wake up from Sleep is possible using
the Autonomous QTouch. Both an IN_TOUCH status change and OUT_OF_TOUCH status
change indication is available when using Autonomous QTouch.
The Autonomous QTouch method acquisition using the CAT module does not require any
Peripheral DMA channel for operation.
DeepStop
Standby
Frozen
Static
Sleep
Mode
Stop
Idle
Autonomous QTouch sensor operation for UC3L
6.3.8.2.
QTouch Group A/B method Disable and Re-enable Sensor for UC3L
Autonomous QTouch Sensor pin selection for UC3L
Autonomous QTouch sensor Schematic for UC3L
Autonomous QTouch method hardware resource requirement for UC3L
CPU
Stop
Stop
Stop
Stop
Stop
Stop
Section
Table 12 Sleep mode support for Autonomous QTouch
HSB
Stop
Stop
Stop
Stop
Stop
Run
6.3.8.1. Any one SNS-SNSK pair between SNS0-SNSK0 and SNS16-
PBA,B
GCLK
Stop
Stop
Stop
Stop
Run
Run
sources
Clock
Stop
Stop
Stop
Run
Run
Run
Osc32
Run
Run
Run
Run
Run
Run
RCSYS
Stop
Run
Run
Run
Run
Run
Bandgap
BOD &
On
On
On
On
Off
Off
Low power
Low power
Low power
Regulator
Full power
Full power
Full power
Voltage
123