ADZS-ICE-100B Analog Devices Inc, ADZS-ICE-100B Datasheet

Page 1

Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106 ICE-100B Emulator User Guide Revision 1.0, September 2009 Part Number 82-000225-01 a ...

Page 2

Copyright Information ©2009 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc. Notice Analog Devices, Inc. reserves the right to make changes ...

Page 3

Trademark and Service Mark Notice The Analog Devices logo, VisualDSP++, Blackfin, TigerSHARC, SHARC, the CROSSCORE logo, EZ-KIT Lite, and EZ-ICE are regis- tered trademarks are registered trademarks of Analog Devices, Inc. All other brand and product names are trademarks or ...

Page 4

...

Page 5

CONTENTS PREFACE Purpose of This Manual ................................................................ viii Intended Audience ........................................................................ viii Manual Contents .......................................................................... viii Technical and Customer Support ..................................................... ix GETTING STARTED Contents of Emulator Package ....................................................... 1-2 PC Configuration ......................................................................... 1-2 USB Installation Tasks .................................................................. 1-2 Verifying ...

Page 6

Designing Custom Processor Boards .............................................. 2-4 Mechanical Specifications ............................................................. 2-4 SUPPORT Technical Support ......................................................................... 3-1 Quality Assurance ......................................................................... 3-2 REFERENCES INDEX vi ICE-100B Emulator User Guide ...

Page 7

PREFACE Thank you for purchasing the ICE-100B Emulator. The ICE-100B emulator is used in conjunction with the VisualDSP++ environment to create, test, and debug advanced processor application software on Analog Devices Blackfin The ICE-100B emulator provides state-of-the-art support for JTAG-compliant ...

Page 8

Purpose of This Manual Purpose of This Manual The ICE-100B Emulator User Guide provides directions for installing the ICE-100B hardware and software on your PC. The manual also describes how to configure and use the components of the ICE-100B emulators. ...

Page 9

Technical and Customer Support You can reach Analog Devices, Inc. Customer Support in the following ways: • Visit the Embedded Processing and DSP products Web site at http://www.analog.com/processors/technical_support • E-mail tools questions to processor.tools.support@analog.com • E-mail processor questions to processor.support@analog.com ...

Page 10

Technical and Customer Support x ICE-100B Emulator User Guide ...

Page 11

GETTING STARTED This chapter provides the information needed to begin using Analog Devices ICE-100B emulators.  Analog Devices emulators are not intended to be used in a production environment. This chapter includes the following sections. • “Contents of Emulator ...

Page 12

Contents of Emulator Package Contents of Emulator Package The ICE-100B emulator package contains the following items: • ICE-100B emulator • 2-meter USB Standard-A to mini-B cable PC Configuration For correct operation of the ICE-100B emulator, your computer must have the ...

Page 13

Note: If you connect the ICE first, before installing VisualDSP++, the Windows driver wizard will not be able to find the drivers to install for the emulator to function. 2. Select the operating voltage of the target DSP JTAG interface. ...

Page 14

USB Installation Tasks Table 1-2. JP2 Settings Jumper Uninstalled Installed 4. Connect the USB cable between the ICE-100B emulator and a USB port of your computer. 5. Verify driver installation. Refer to on page 1-4.  Before connecting to a ...

Page 15

Figure 1-2. Verifying Driver Installation ICE-100B Emulator User Guide Getting Started 1-5  ...

Page 16

Attaching to the Emulation Target Attaching to the Emulation Target The final step is to connect the 14-pin header (J1) of the ICE-100B emu- lator to the target board via the JTAG interface. The 14-pin connector is keyed at pin ...

Page 17

Powering Up/Down the ICE-100B Emulator To power up the ICE-100B emulator: 1. Apply power to the target board. 2. Connect the USB port on the computer to the ICE-100B emula- tor.  The ICE-100B is a bus-powered device, so this ...

Page 18

VisualDSP++ Configurator VisualDSP++ Configurator VisualDSP++ requires a description of the platform (JTAG chain). The platform definition is necessary for VisualDSP++ to communicate with the hardware through the emulator. The VisualDSP++ Configurator and ICE Test utilities allow configuration and testing of ...

Page 19

Troubleshooting and Warranty Information To provide comprehensive troubleshooting advice and warranty information for all emulator and EZ-KIT Lite products, Analog Devices maintains an Engineer-to-Engineer Note to provide this information. Emulator and EZ-KIT Lite Evaluation System Troubleshooting Guide (EE-175), is available ...

Page 20

Troubleshooting and Warranty Information 1-10 ICE-100B Emulator User Guide ...

Page 21

HARDWARE DESCRIPTION This chapter describes the hardware design of the ICE-100B emulator and includes the following sections: • “LEDs” on page Describes LEDs which inform you of the emulator’s status. • “Resetting the Target” on page Describes how to ...

Page 22

... Resetting the Target PN: ADZS-ICE-100B Figure 2-1. LED Positions - Top of Emulator Board Resetting the Target When debugging remotely, the ability to reset the target can be very use- ful. Enable this function through the Reset Target Options dialog box and by soldering a wire from the ICE-100B emulator to the target. Two solder points labeled “ ...

Page 23

To Reset the Target • From the Debug menu, choose Reset Target.  This sends a reset pulse of the specified Reset Time duration to the target. Reset Target Options Dialog Box Use the Reset Target Options dialog box (refer ...

Page 24

Designing Custom Processor Boards Designing Custom Processor Boards When designing a custom processor board using Analog Devices processors and DSPs, special care must be taken to ensure that the JTAG interface is designed and laid out correctly. If the board ...

Page 25

... P3 0.785” * 0.235” 0.310” 0.070” 0.093” J1 Figure 2-3. ICE-100B Emulator Dimensions (in inches) ICE-100B Emulator User Guide Hardware Description 2.990” PN: ADZS-ICE-100B 3.3 1.8 JP1 a ICE-100B * = MAXIMUM COMPONENT HEIGHT STAT PWR LED3 LED1 2.5 LED2 JP2 JP1 0.045” ...

Page 26

Mechanical Specifications 2-6 ICE-100B Emulator User Guide ...

Page 27

SUPPORT Analog Devices provides free technical support. Technical Support For technical support, visit the Embedded Processing and DSP Technical Support page at: http://www.analog.com/processors/technical_support From there you can: • Access the EngineerZone DSP Support Forum where Analog Devices support team ...

Page 28

Quality Assurance Quality Assurance Analog Devices is committed to providing quality products and services. To continually provide this quality, please contact our Quality Assurance Department directly if you have any concerns at (603) 883-2430, Monday through Friday during normal business ...

Page 29

REFERENCES This section describes documentation resources helpful in your application development. • For information on designing the interface between an Analog Devices processor and the emulation header on your custom processor target board, refer to Engineer-to-Engineer Note, Analog Devices ...

Page 30

For information about digital signal processing theory and applications, consult: Higgins. Digital Signal Processing In VLSI.   Prentice-Hall, 1990. Oppenheim and Schafer. Digital Signal Processing.  Prentice-Hall, 1975. 4-2 ICE-100B Emulator User Guide ...

Page 31

I INDEX A attaching JTAG cable, 1-6 C contents, emulator package, 1-2 customer support, -ix custom processor boards, 2-4 D data sheets, 4-1 designing custom boards, 2-4 Device Manager window, 1-4 digital signal processing theory, documentation resources, 4-1 drivers, 1-4 ...

Page 32

Q quality assurance, 3-2 R resetting the target, 2-2 T target, resetting, 2-2 technical support, 3-1 I-2 V verifying driver installation, 1-4 VisualDSP++, -vii, 1-2 documentation, 4-1 VisualDSP++ Configurator, 1-8 W Windows operation, 1-3 ICE-100B Emulator User Guide ...