ESDA6V1-5M6 STMicroelectronics, ESDA6V1-5M6 Datasheet

Page 1

... Printers ■ Communication systems ■ Cellular phone handsets and accessories ■ Video equipment February 2008 ESDA6V1M6, ESDA6V1-5M6 4- and 5-line Transil™ arrays for ESD protection Figure 1. ² Description The ESDA6V1xxM6 are monolithic arrays designed to protect lines against ESD transients. The device is ideal for applications where both reduced print circuit board space and power absorption capability are required ...

Page 2

... ( DC MHz amb 2/11 amb Parameter ( °C) amb Parameter RM Test Condition = 30 mV osc RMS - 25 ° (25 °C) BR ESDA6V1M6, ESDA6V1-5M6 = 25 °C) Value ±15 ± initial = T 100 j amb 125 -55 to +150 260 -40 to +125 Slope Min Typ Max 6.1 7.2 500 Unit °C °C ° ...

Page 3

... ESDA6V1M6, ESDA6V1-5M6 Figure 2. Relative variation of peak pulse power versus initial junction temperature °C 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 Figure 4. Clamping voltage versus peak pulse current (typical values, 8/20 µs waveform) 100.0 8/20µs T initial =25° ...

Page 4

... Package M6 = Micro QFN 6 leads 4/11 Figure 9. 0.00 -30.00 -60.00 -90.00 -120.00 100.0M 1.0G Figure 11. ESD response to IEC 6100-4-2 ESDA6V1M6, ESDA6V1-5M6 Analog crosstalk measurements between channels dB f/Hz 100.0k 1.0M 10.0M 100.0M (-15 kV air discharge) on each channel ESDA 6V1 ...

Page 5

... ESDA6V1M6, ESDA6V1-5M6 3 Package information ● Epoxy meets UL94 order to meet environmental requirements, ST offers these devices in ECOPACK packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label ...

Page 6

... PCB. Only pin 1 mark used for this purpose. 6/11 Dot identifying Pin A1 location Dot identifying Pin A1 location 4.00+/-0.1 4.00+/-0.1 2.0+/-0.05 2.0+/-0. 0.75 0.75 1.20 1.20 User direction of unreeling User direction of unreeling X: Marking X: Marking ESDA6V1M6, ESDA6V1-5M6 1.5 +/- 0.1 1.5 +/- 0 4.00 4.00 ...

Page 7

... ESDA6V1M6, ESDA6V1-5M6 4 Recommendation on PCB assembly 4.1 Stencil opening design 1. General recommendation on stencil opening design a) Stencil opening dimensions: L (Length), W (Width), T (Thickness). Figure 15. Stencil opening dimensions b) General design rule Stencil thickness ( 125 µm Aspect Ratio Aspect Area 2. Reference design a) Stencil opening thickness: 100 µm b) Stencil opening for leads: Opening to footprint ratio is 90% ...

Page 8

... To control the solder paste amount, the closed via is recommended instead of open vias. 2. The position of tracks and open vias in the solder area should be well balanced. The symmetrical layout is recommended, in case any tilt phenomena caused by asymmetrical solder paste amount due to the solder flow away. 8/11 ESDA6V1M6, ESDA6V1-5M6 ...

Page 9

... ESDA6V1M6, ESDA6V1-5M6 4.5 Reflow profile Figure 17. ST ECOPACK® recommended soldering reflow profile for PCB mounting Temperature (°C) Temperature (°C) 260°C max 260°C max 255°C 255°C 220°C 220°C 180°C 180°C 125 °C 125 °C ...

Page 10

... Package title changed from DFN to QFN. No technical changes. Reformatted to current standard. 3 Added note on marking rotation in section 3. Package information. Reformatted to current standards. Corrected inch measurements in 4 Table 3 on page 5. Added assembly. ESDA6V1M6, ESDA6V1-5M6 Weight Base qty Delivery mode 2.2 mg 3000 Tape and reel 2.2 mg 3000 ...

Page 11

... ESDA6V1M6, ESDA6V1-5M6 Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...