PIC12F635-I/MD Microchip Technology, PIC12F635-I/MD Datasheet - Page 109

• Manufacturer Part Number: PIC12F635-I/MD
• Description: IC PIC MCU FLASH 1KX14 8DFN
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F635-I/MD

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 5
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DFN
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 64Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164326 - MODULA SKT PM3 20QFNXLT08DFN2 - SOCKET TRANSITION ICE 14DIP/8DFNAC162057 - MPLAB ICD 2 HEADER 14DIPXLT08DFN - SOCKET TRANSITION ICE 8DFN
• Data Converters: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

11.20 Soft Reset
The AFE issues a Soft Reset in the following events:
a)
b)
c)
d)
The “Abort” occurs if there is no positive signal
detected at the end of the AGC stabilization period
(T
brings the AFE into a low current Standby mode
operation. The internal circuits that are initialized by the
Soft Reset include:
• Output Enable Filter
• AGC circuits
• Demodulator
• 32 kHz Internal Oscillator
The Soft Reset has no effect on the Configuration register
setup, except for some of the AFE Status Register 7 bits.
(Register 11-8).
The circuit initialization takes one internal clock cycle
(1/32 kHz = 31.25
modulation transistors between each input and
LCCOM pins are turned-on to discharge any inter-
nal/external parasitic charges. The modulation transis-
tors are turned-off immediately after the initialization
time.
The Soft Reset is executed in Active mode only. It is not
valid in Standby mode.
11.21 Minimum Modulation Depth
The AFE demodulates the modulated input signal if the
modulation depth of the input signal is greater than the
minimum requirement that is programmed in the AFE
Configuration Register 5 (Register 11-6). Figure 11-7
shows the definition of the modulation depth and
examples. MODMIN<6:5> of the Configuration Register
5 offer four options. They are 75%, 50%, 25% and 12%,
with a default setting of 50%.
The purpose of this feature is to enhance the
demodulation integrity of the input signal. The 12%
setting is the best choice for the input signal with weak
modulation depth, which is typically observed near the
high-voltage base station antenna and also at
far-distance from the base station antenna. It gives the
best demodulation sensitivity, but is very susceptible to
noise spikes that can result in a bit detection error. The
75% setting can reduce the bit errors caused by noise,
but gives the least demodulation sensitivity. See
Table 11-3 for minimum modulation depth requirement
settings.
© 2007 Microchip Technology Inc.
AGC
After Power-on Reset (POR),
After Inactivity timer time-out,
If an “Abort” occurs,
After receiving SPI Soft Reset command.
). The Soft Reset initializes internal circuits and
Requirement for Input Signal
s). During the initialization, the
PIC12F635/PIC16F636/639
TABLE 11-3:
(Config. Register 5)
Bit 6
MODMIN Bits
0
0
1
1
Bit 5
SETTING FOR MINIMUM
MODULATION DEPTH
REQUIREMENT
0
1
0
1
Modulation Depth
50% (default)
DS41232D-page 107
75%
25%
12%