AT89LS52-16JU Atmel, AT89LS52-16JU Datasheet - Page 23

• Manufacturer Part Number: AT89LS52-16JU
• Description: IC MCU 8K FLASH 16MHZ 44-PLCC
• Manufacturer: Atmel
• Series: 89LSr

Specifications of AT89LS52-16JU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: UART/USART
• Peripherals: WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 4 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 4 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89ISP
• Minimum Operating Temperature: - 40 C
• Cpu Family: 89LS
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 256Byte
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 4V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PLCC
• Package: 44PLCC
• Family Name: 89LS
• Maximum Speed: 16 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.1
19.2
2601C–MICRO–06/08
Serial Programming Algorithm
Serial Programming Instruction Set
To program and verify the AT89LS52 in the serial programming mode, the following sequence is
recommended:
If a crystal is not connected across pins XTAL1 and XTAL2, apply a 3 MHz to 16 MHz clock to
XTAL1 pin and wait for at least 10 milliseconds.
Power-off sequence (if needed):
Data Polling: The Data Polling feature is also available in the serial mode. In this mode, during
a byte write cycle an attempted read of the last byte written will result in the complement of the
MSB of the serial output byte on MISO.
The Instruction Set for Serial Programming follows a 4-byte protocol and is shown in
1. Power-up sequence:
2. Enable serial programming by sending the Programming Enable serial instruction to pin
3. The Code array is programmed one byte at a time in either the Byte or Page mode. The
4. Any memory location can be verified by using the Read instruction which returns the
5. At the end of a programming session, RST can be set low to commence normal device
1. Set XTAL1 to “L” (if a crystal is not used).
2. Set RST to “L”.
3. Turn V
a. Apply power between VCC and GND pins.
b. Set RST pin to “H”.
MOSI/P1.5. The frequency of the shift clock supplied at pin SCK/P1.7 needs to be less
than the CPU clock at XTAL1 divided by 16.
write cycle is self-timed and typically takes less than 1 ms at 2.7V.
content at the selected address at serial output MISO/P1.6.
operation.
CC
power off.
AT89LS52
Table
22-1.
23