PIC16F628A-I/P Microchip Technology, PIC16F628A-I/P Datasheet - Page 80

• Manufacturer Part Number: PIC16F628A-I/P
• Description: IC MCU FLASH 2KX14 EEPROM 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F628A-I/P

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 128 x 8
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 224 B
• Interface Type: SCI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• Package: 18PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3DBF648 - BOARD DAUGHTER ICEPIC3AC162053 - HEADER INTERFACE ICD,ICD2 18DIPACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F627A/628A/648A
FIGURE 12-1:
Follow these steps when setting up an Asynchronous
Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
FIGURE 12-2:
DS40044F-page 78
TXIF bit
(Transmit buffer
TRISB<1> and TRISB<2> should both be set to
‘1’ to configure the RB1/RX/DT and RB2/TX/CK
pins as inputs. Output drive, when required, is
controlled by the peripheral circuitry.
Initialize the SPBRG register for the appropriate
baud rate. If a high-speed baud rate is desired,
set bit BRGH. (Section 12.1 “USART Baud
Rate Generator (BRG)”).
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, then set enable bit
TXIE.
If 9-bit transmission is desired, then set transmit
bit TX9.
Enable the transmission by setting bit TXEN,
which will also set bit TXIF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Load data to the TXREG register (starts
transmission).
RB2/TX/CK (pin)
reg. empty flag)
TRMT bit
(Transmit shift
reg. empty flag)
Write to TXREG
BRG output
(shift clock)
TXIE
Interrupt
USART TRANSMIT BLOCK DIAGRAM
ASYNCHRONOUS TRANSMISSION
TXIF
TXEN
Baud Rate Generator
Word 1
Transmit Shift Reg.
Word 1
SPBRG
Baud Rate CLK
Start bit
MSb
(8)
TX9D
bit 0
TSR register
TX9
TXREG register
² ² ²
8
Data Bus
bit 1
Word 1
LSb
0
TRMT
Pin Buffer
and Control
bit 7/8
© 2007 Microchip Technology Inc.
SPEN
Stop bit
RB2/TX/CK pin