PIC24HJ32GP204-I/PT Microchip Technology, PIC24HJ32GP204-I/PT Datasheet - Page 90

• Manufacturer Part Number: PIC24HJ32GP204-I/PT
• Description: IC PIC MCU FLASH 32K 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ32GP204-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 32KB (11K x 24)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 13x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24HJ32GP202/204 AND PIC24HJ16GP304
8.1
The PIC24HJ32GP202/204 and PIC24HJ16GP304
devices provide the following seven system clock
options.
• Fast RC (FRC) Oscillator
• FRC Oscillator with PLL
• Primary (XT, HS or EC) Oscillator
• Primary Oscillator with PLL
• Secondary (LP) Oscillator
• Low-Power RC (LPRC) Oscillator
• FRC Oscillator with postscaler
8.1.1
8.1.1.1
The Fast RC (FRC) internal oscillator runs at a nominal
frequency of 7.37 MHz. User software can tune the
FRC frequency. User software can optionally specify a
factor (ranging from 1:2 to 1:256) by which the FRC
clock frequency is divided. This factor is selected using
the FRCDIV<2:0> bits (CLKDIV<10:8>).
8.1.1.2
The primary oscillator can use one of the following as
its clock source:
• Crystal (XT): Crystals and ceramic resonators in
• HS (High-Speed Crystal): Crystals in the range of
• EC (External Clock): The external clock signal is
8.1.1.3
The secondary (LP) oscillator is designed for low power
and uses a 32.768 kHz crystal or ceramic resonator.
The LP oscillator uses SOSCI and SOSCO pins.
8.1.1.4
The Low-Power RC (LPRC) internal oscIllator runs at a
nominal frequency of 32.768 kHz. It is also used as a
reference clock by the Watchdog Timer (WDT) and
Fail-Safe Clock Monitor (FSCM).
8.1.1.5
The clock signals generated by the FRC and primary
oscillators can be optionally applied to an on-chip
Phase Locked Loop (PLL) to provide a wide range of
output
configuration is described in
Configuration”.
The FRC frequency depends on the FRC accuracy
(see
Tuning register (see
DS70289G-page 90
the range of 3.5 MHz to 10 MHz. The crystal is
connected to the OSC1 and OSC2 pins.
10 MHz to 40 MHz. The crystal is connected to
the OSC1 and OSC2 pins.
directly applied to the OSC1 pin.
Table
frequencies
CPU Clocking System
22-18) and the value of the FRC Oscillator
SYSTEM CLOCK SOURCES
Fast RC
Primary
Secondary
Low-Power RC
FRC
Register
for
device
8-4).
Section 8.1.3 “PLL
operation.
PLL
8.1.2
The oscillator source used at a device Power-on Reset
event is selected using Configuration bit settings. The
oscillator Configuration bit settings are located in the
Configuration registers in the program memory. (Refer to
Section 19.1 “Configuration Bits”
The Initial Oscillator Selection Configuration bits,
FNOSC<2:0> (FOSCSEL<2:0>), and the Primary
Oscillator
POSCMD<1:0> (FOSC<1:0>), select the oscillator
source that is used at a Power-on Reset. The FRC
primary oscillator is the default (unprogrammed)
selection.
The Configuration bits allow users to choose among 12
different clock modes, shown in
The output of the oscillator (or the output of the PLL if
a PLL mode has been selected) F
generate the device instruction clock (F
peripheral clock time base (F
operating speed of the device, and speeds up to 40
MHz are supported by the PIC24HJ32GP202/204 and
PIC24HJ16GP304 architecture.
Instruction execution speed or device operating
frequency, F
EQUATION 8-1:
8.1.3
The primary oscillator and internal FRC oscillator can
optionally use on-chip PLL to obtain higher speeds of
operation. The PLL provides significant flexibility in
selecting the device operating speed. A block diagram
of the PLL is shown in
The output of the primary oscillator or FRC, denoted as
‘F
... or 33 before it is being provided to the PLL’s Voltage
Controlled Oscillator (VCO). The input to the VCO must
be selected in the range of 0.8 MHz to 8 MHz. The
prescale
PLLPRE<4:0> bits (CLKDIV<4:0>).
The PLL Feedback Divisor, selected using the
PLLDIV<8:0> bits (PLLFBD<8:0>), provides a factor ‘M’,
by which the input to the VCO is multiplied. This factor
must be selected such that the resulting VCO output
frequency is in the range of 100 MHz to 200 MHz.
The VCO output is further divided by a postscale factor
‘N2.’ This factor is selected using the PLLPOST<1:0>
bits (CLKDIV<7:6>). ‘N2’ can be 2, 4 or 8, and must be
selected such that the PLL output frequency (F
in the range of 12.5 MHz to 80 MHz, which generates
device operating speeds of 6.25-40 MIPS.
IN
’ is divided down by a prescale factor (N1) of 2, 3,
factor
SYSTEM CLOCK SELECTION
PLL CONFIGURATION
CY
Mode
, is given by:
‘N1’
F
CY
DEVICE OPERATING
FREQUENCY
Figure
Select
© 2011 Microchip Technology Inc.
=
is
F
-------------
OSC
8-2.
2
selected
Table
P
Configuration
OSC
). F
for further details.)
is divided by 2 to
8-1.
CY
CY
defines the
using
) and the
OSC
bits,
the
) is