DSPIC33FJ16MC304-I/ML Microchip Technology, DSPIC33FJ16MC304-I/ML Datasheet - Page 205

• Manufacturer Part Number: DSPIC33FJ16MC304-I/ML
• Description: IC DSPIC MCU/DSP 16K 44QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16MC304-I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 9x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 35
• Flash Memory Size: 16KB
• Supply Voltage Range: 3V To 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164335 - MODULE SKT FOR 10X10 PM3 44TQFPDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

15.0
FIGURE 15-1:
© 2009 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
2: Some registers and associated bits
OUTPUT COMPARE
of
dsPIC33FJ64MCX02/X04
dsPIC33FJ128MCX02/X04
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Section 13. Output
Compare” (DS70209) of the “dsPIC33F/
PIC24H
which is available from the Microchip
website (www.microchip.com).
described in this section may not be avail-
able on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
the
16
TMR2
OUTPUT COMPARE MODULE BLOCK DIAGRAM
Family
Comparator
0
OCxRS
OCxR
dsPIC33FJ32MC302/304,
TMR3
1
Reference
16
OCTSEL
family
Manual”,
Rollover
TMR2
and
0
Preliminary
of
Rollover
TMR3
1
Mode Select
OCM<2:0>
The Output Compare module can select either Timer2
or Timer3 for its time base. The module compares the
value of the timer with the value of one or two compare
registers depending on the operating mode selected.
The state of the output pin changes when the timer
value matches the compare register value. The Output
Compare module generates either a single output
pulse or a sequence of output pulses, by changing the
state of the output pin on the compare match events.
The Output Compare module can also generate
interrupts on compare match events.
The Output Compare module has multiple operating
modes:
• Active-Low One-Shot mode
• Active-High One-Shot mode
• Toggle mode
• Delayed One-Shot mode
• Continuous Pulse mode
• PWM mode without fault protection
• PWM mode with fault protection
Output
Logic
3
Set Flag bit
OCxIF
R
S
Q
Output Enable
DS70291D-page 205
OCx
OCFA