PIC18LF6310-I/PT Microchip Technology, PIC18LF6310-I/PT Datasheet - Page 8

• Manufacturer Part Number: PIC18LF6310-I/PT
• Description: IC PIC MCU FLASH 4KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF6310-I/PT

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 54
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• No. Of Pwm: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
17. Module: External Memory Bus (EMB)
18. Module: EUSART
19. Module: EUSART
20. Module: EUSART
DS80206F-page 8
When the EMB is enabled and configured for 8-bit
mode and EBDIS (MEMCON<7>) is clear, the BA0
pin continues to be active during table read and
table write operations to internal program memory
addresses. Under these conditions, BA0 should
be inactive.
Work around
Set the EBDIS bit when performing table
operations to internal program memory.
Date Codes that pertain to this issue:
All engineering and production devices.
The EUSART auto-baud feature may periodically
measure the incoming baud rate incorrectly. The
rate of incorrect baud rate measurements will
depend on the frequency of the incoming
synchronization byte and the system clock
frequency.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode (SYNC = 1) with clock
polarity high (SCKP = 1), the EUSART transmits a
shorter than expected clock on the CKx pin for
bit 0.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode, EUSART baud rates using
SPBRGx values of ‘0’ and ‘1’ may not function
correctly.
Work around
Use another baud rate configuration to generate
the desired baud rate.
Date Codes that pertain to this issue:
All engineering and production devices.
21. Module: MSSP
22. Module: MSSP
23. Module: MSSP
In an I
unaddressed slave may respond to bus activity
when data on the bus matches its address. The
first occurrence will set the BF bit. The second
occurrence will set the BF and SSPOV bits. In both
situations, the SSPIF bit is not set and an interrupt
will not occur. The device will vector to the Interrupt
Service Routine only if the interrupt is enabled and
an address match occurs.
Work around
The I
I
Date Codes that pertain to this issue:
All engineering and production devices.
In I
work correctly.
Work around
Use a BRG value greater than ‘0’ by setting
SSPADD ≥ 1.
Date Codes that pertain to this issue:
All engineering and production devices.
In I
ware to begin data reception and cleared by the
peripheral after a byte is received. After a byte is
received, the device may take up to 80 T
RCEN and 800 T
and MPLAB ICE emulators.
Work around
Single byte receptions are typically not affected,
since the delay between byte receptions is
typically long enough for the RCEN bit to clear. For
multiple byte receptions, the software must wait
until the bit is cleared by the peripheral before the
next byte can be received.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C address match to maintain normal operation.
2
2
C Master mode, the BRG value of ‘0’ may not
C Master mode, the RCEN bit is set by soft-
2
C slave must clear the SSPOV bit after each
2
C™ system with multiple slave nodes, an
CY
© 2007 Microchip Technology Inc.
when using MPLAB
CY
®
to clear
ICD 2