PIC16C63A-04I/SP Microchip Technology, PIC16C63A-04I/SP Datasheet - Page 49

• Manufacturer Part Number: PIC16C63A-04I/SP
• Description: IC MCU OTP 4KX14 PWM 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C63A-04I/SP

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 22
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 22
• Ram Memory Size: 192Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVMCPA - KIT DVR BOARD EVAL SYSTEM MXDEV1
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

9.0
Each Capture/Compare/PWM (CCP) module contains
a 16-bit register which can operate as a:
• 16-bit Capture register
• 16-bit Compare register
• PWM Master/Slave Duty Cycle register
Both the CCP1 and CCP2 modules are identical in
operation, with the exception being the operation of the
special event trigger. Table 9-1 and Table 9-2 show the
resources and interactions of the CCP module(s). In
the following sections, the operation of a CCP module
is described with respect to CCP1. CCP2 operates the
same as CCP1, except where noted.
CCP1 Module:
Capture/Compare/PWM Register1 (CCPR1) is com-
prised of two 8-bit registers: CCPR1L (low byte) and
CCPR1H (high byte). The CCP1CON register controls
the operation of CCP1. The special event trigger is
generated by a compare match and will reset Timer1.
TABLE 9-2:
CCPx Mode CCPy Mode
Capture
Capture
Compare
PWM
PWM
PWM
2000 Microchip Technology Inc.
CAPTURE/COMPARE/PWM
MODULES
Capture
Compare
Compare
PWM
Capture
Compare
INTERACTION OF TWO CCP MODULES
Same TMR1 time-base.
The compare should be configured for the special event trigger, which clears TMR1.
The compare(s) should be configured for the special event trigger, which clears TMR1.
The PWMs will have the same frequency and update rate (TMR2 interrupt).
None.
None.
PIC16C63A/65B/73B/74B
CCP2 Module:
Capture/Compare/PWM Register2 (CCPR2) is com-
prised of two 8-bit registers: CCPR2L (low byte) and
CCPR2H (high byte). The CCP2CON register controls
the operation of CCP2. The special event trigger is
generated by a compare match and will reset Timer1
and start an A/D conversion (if the A/D module is
enabled).
Additional information on CCP modules is available in
the PICmicro™ Mid-Range MCU Family Reference
Manual (DS33023) and in “Using the CCP Modules”
(AN594).
TABLE 9-1:
Interaction
CCP Mode
Compare
Capture
PWM
CCP MODE - TIMER
RESOURCES REQUIRED
Timer Resource
DS30605C-page 49
Timer1
Timer1
Timer2