ATMEGA32A-PU Atmel, ATMEGA32A-PU Datasheet - Page 243

• Manufacturer Part Number: ATMEGA32A-PU
• Description: MCU AVR 32K FLASH 16MHZ 40-PDIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 40PDIP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Rom Size: 1024 B
• Height: 4.83 mm
• Length: 52.58 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 13.97 mm
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 24-4.
24.5.6
Figure 24-10
Figure 24-9
inputs are shared with a digital port pin as well.
Figure 24-10. Analog to Digital Converter
The signals are described briefly in
8155C–AVR–02/11
Signal
Name
AC_IDLE
ACO
ACME
ACBG
NEGSEL_2
NEGSEL_1
NEGSEL_0
MUXEN_7
MUXEN_6
MUXEN_5
MUXEN_4
MUXEN_3
MUXEN_2
MUXEN_1
MUXEN_0
EXTCH
ADC_7
ADC_6
ADC_5
ADC_4
ADC_3
ADC_2
ADC_1
ADC_0
Scanning the ADC
is attached to each of these signals. The ADC need not be used for pure connectivity testing, since all analog
shows a block diagram of the ADC with all relevant control and observe signals. The Boundary-scan cell from
ADC_2
ADC_0
ADC_1
Direction as Seen from
the Comparator
Input
Output
Input
Input
Boundary-scan Signals for the Analog Comparator
SCTEST
AMPEN
ACLK
G10
ST
Table
To Comparator
Description
Turns off Analog
comparator when true
Analog Comparator
Output
Uses output signal from
ADC mux when true
Bandgap Reference
enable
+
-
10x
24-5.
G20
ADCBGEN
VCCREN
IREFEN
AREF
PASSEN
+
-
20x
1.22V
GNDEN
ACTEN
ref
Recommended Input
when Not in Use
Will become input to µC
code being executed
2.56V
ref
1
0
0
PRECH
DAC_9..0
ADCEN
HOLD
PRECH
AREF
Output Values when
Recommended Inputs are Used
Depends upon µC code being
executed
0
Depends upon µC code being
executed
Depends upon µC code being
executed
10-bit DAC
AREF
ATmega32A
+
-
DACOUT
COMP
243