PIC24FJ128GA008-I/PT Microchip Technology, PIC24FJ128GA008-I/PT Datasheet - Page 3

• Manufacturer Part Number: PIC24FJ128GA008-I/PT
• Description: IC PIC MCU FLASH 128K 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ128GA008-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (43K x 24)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 69
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011, DV164033, MA240011, AC164127
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Controller Family/series: PIC24
• No. Of I/o's: 69
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Embedded Interface Type: EUART, I2C, PSP, SPI
• Rohs Compliant: Yes
• Package: 80TQFP
• Device Core: PIC
• Family Name: PIC24
• Maximum Speed: 16 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM240011 - KIT STARTER MPLAB FOR PIC24F MCUMA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.2
The Flash program memory on the PIC24FJXXXGA0XX
devices has a specific write/erase requirement that must
be adhered to for proper device operation. The rule is
that any given word in memory must not be written more
than twice before erasing the page in which it is located.
Thus, the easiest way to conform to this rule is to write
all the data in a programming block within one write
cycle. The programming methods specified in this
specification comply with this requirement.
TABLE 2-1:
© 2008 Microchip Technology Inc.
MCLR
ENVREG
DISVREG
V
V
V
PGC1
PGD1
PGC2
PGD2
Legend: I = Input, O = Output, P = Power
Note 1:
Note:
DD
SS
DDCORE
Pin Name
and AV
and AV
2:
Program Memory Write/Erase
Requirements
(1)
Applies to 28 and 44-pin devices only.
All power supply and ground pins must be connected, including analog supplies (AV
(AV
Writing to a location multiple times without
erasing is not recommended.
SS
DD
(2)
SS
(2)
).
PIN DESCRIPTIONS (DURING PROGRAMMING)
Pin Name
DISVREG
ENVREG
V
MCLR
DDCORE
PGC
PGD
PGC
PGD
V
V
DD
SS
Pin Type
I/O
I/O
P
P
P
P
I
I
I
I
Programming Enable
Enable for On-Chip Voltage Regulator
Disable for On-Chip Voltage Regulator
Power Supply
Ground
Regulated Power Supply for Core
Primary Programming Pin Pair: Serial Clock
Primary Programming Pin Pair: Serial Data
Secondary Programming Pin Pair: Serial Clock
Secondary Programming Pin Pair: Serial Data
During Programming
2.3
The pin diagrams for the PIC24FJXXXGA0XX family
are shown in the following figures. The pins that are
required for programming are listed in Table 2-1 and
are shown in bold letters in the figures. Refer to the
appropriate device data sheet for complete pin
descriptions.
PIC24FJXXXGA0XX
Pin Diagrams
Pin Description
DD
) and ground
DS39768D-page 3