PIC18LF2523-I/SO Microchip Technology, PIC18LF2523-I/SO Datasheet - Page 16
![IC PIC MCU FLASH 16KX16 28SOIC](/photos/6/59/65909/150-28-soic_sml.jpg)
PIC18LF2523-I/SO
Manufacturer Part Number
PIC18LF2523-I/SO
Description
IC PIC MCU FLASH 16KX16 28SOIC
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC18F2221-ISO.pdf
(46 pages)
2.PIC18F2423-ISP.pdf
(54 pages)
3.PIC18F2423-ISP.pdf
(8 pages)
4.PIC18F2423-ISP.pdf
(34 pages)
5.PIC18F2523-ISO.pdf
(392 pages)
Specifications of PIC18LF2523-I/SO
Core Size
8-Bit
Program Memory Size
32KB (16K x 16)
Core Processor
PIC
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
25
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 10x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Controller Family/series
PIC18
No. Of I/o's
25
Eeprom Memory Size
256Byte
Ram Memory Size
1.5KB
Cpu Speed
40MHz
No. Of Timers
4
Processor Series
PIC18LF
Core
PIC
Data Bus Width
8 bit
Data Ram Size
1.5 KB
Interface Type
EUSART, I2C, MSSP, SPI
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
25
Number Of Timers
4
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM163022, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
12 bit, 10 Channel
A/d Bit Size
12 bit
A/d Channels Available
10
Height
2.31 mm
Length
17.9 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2 V
Width
7.5 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
PIC18F2423/2523/4423/4523
3.3
Data EEPROM is accessed one byte at a time via an
Address Pointer (register pair EEADRH:EEADR) and a
data latch (EEDATA). Data EEPROM is written by
loading EEADRH:EEADR with the desired memory
location, EEDATA with the data to be written and initiat-
ing a memory write by appropriately configuring the
EECON1 register. A byte write automatically erases the
location and writes the new data (erase-before-write).
When using the EECON1 register to perform a data
EEPROM write, both the EEPGD and CFGS bits must
be cleared (EECON1<7:6> = 00). The WREN bit must
be set (EECON1<2> = 1) to enable writes of any sort
and this must be done prior to initiating a write
sequence. The write sequence is initiated by setting the
WR bit (EECON1<1> = 1).
The write begins on the falling edge of the 4th PGC
after the WR bit is set. It ends when the WR bit is
cleared by hardware.
After the programming sequence terminates, PGC must
still be held low for the time specified by parameter P10
to allow high-voltage discharge of the memory array.
FIGURE 3-7:
DS39759A-page 16
PGC
PGD
Poll WR bit
Data EEPROM Programming
4-Bit Command
1
0
2
0
3
0
4
PGD
0
PGC
P5
DATA EEPROM WRITE TIMING
BSF EECON1, WR
1
4-Bit Command
2
1
0
2
0
15 16
3
0
4
0
P5A
P5
MOVF EECON1, W, 0
1
2
PGD = Input
PGD = Input
15 16
P5A
4-Bit Command
1
Poll WR bit, Repeat until Clear
0
FIGURE 3-6:
2
0
3
0
P11A
(see below)
4
0
P5
MOVWF TABLAT
1
No
2
15 16
PROGRAM DATA FLOW
Enable Write
Set Address
Start Write
Sequence
© 2005 Microchip Technology Inc.
Set Data
Done?
WR bit
clear?
Done
Start
P5A
Yes
Yes
(see Figure 4-4)
PGD = Output
Shift Out Data
No
P10
16-Bit Data
Payload
1
n
2
n