DSPIC30F4013-30I/P Microchip Technology, DSPIC30F4013-30I/P Datasheet - Page 2

• Manufacturer Part Number: DSPIC30F4013-30I/P
• Description: IC DSPIC MCU/DSP 48K 40DIP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F4013-30I/P

• Program Memory Type: FLASH
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, POR, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 48KB (16K x 24)
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• Maximum Clock Frequency: 40 MHz
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Data Rom Size: 1024 B
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, DM240002, DM300018, DM330011
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC30F003 - MODULE SOCKET DSPIC30F 40DIPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLEACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: DSPIC30F4013-30IP

dsPIC30F Family Reference Manual
35.1
Figure 35-1:
DS70272B-page 35-2
SDO1
SCK1
SDI1
SS1
Introduction
Read SPI1BUF
SPI1 Module Block Diagram
Control
Sync
Transfer
The Serial Peripheral Interface (SPI) module is a synchronous serial interface useful for
communicating with other peripheral or microcontroller devices. These peripheral devices may
be serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SPI module is
compatible with Motorola’s SPI and SIOP interfaces.
Each device in the dsPIC30F SMPS and Digital Power Conversion device family offers one SPI
module, designated SPI1.
The SPI1 serial interface consists of four pins:
• SDI1: Serial Data Input
• SDO1: Serial Data Output
• SCK1: Shift Clock Input or Output
• SS1: Active-Low Slave Select or Frame Synchronization I/O Pulse
The SPI1 module can be configured to operate using 2, 3 or 4 pins. In the 3-pin mode, SS1 is
not used. In the 2-pin mode, SDO1 and SS1 are both unused.
A block diagram of the SPI1 module is shown in Figure 35-1.
Note:
SPI1RXB
bit 0
Some devices in the dsPIC30F SMPS and Digital Power Conversion device family
do not contain the SS1 pin and, therefore, do not include the Framed SPI and Slave
Select functions. Refer to the specific device data sheet for details about available
SPI pins.
SPI1BUF
SPI1SR
Control
Clock
Shift Control
SPI1TXB
Transfer
Write SPI1BUF
Select
Edge
16
Secondary
1:1 to 1:8
Prescaler
Internal Data Bus
1:1/4/16/64
Prescaler
Primary
© 2008 Microchip Technology Inc.
F
SPI1CON1<1:0>
SPI1CON1<4:2>
Enable
Master Clock
CY