PIC18F4610-I/P Microchip Technology, PIC18F4610-I/P Datasheet - Page 2

• Manufacturer Part Number: PIC18F4610-I/P
• Description: IC MCU FLASH 32KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4610-I/P

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3968 B
• Interface Type: CCP/ECCP/EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Data Rom Size: 3968 B
• Height: 3.81 mm
• Length: 52.26 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 13.84 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2515/2610/4515/4610
2. Module: MSSP
3. Module: Enhanced
DS80281C-page 2
With MSSP in SPI Master mode, F
Timer2/2 clock rate and CKE = 0, a write collision
may occur if SSPBUF is loaded immediately after
the transfer is complete. A delay may be required
after the MSSP Interrupt Flag bit, SSPIF, is set or
the Buffer Full bit, BF, is set and before writing
SSPBUF. If the delay is insufficiently short, a write
collision may occur as indicated by the WCOL bit
being set.
Work around
Add a software delay of one SCK period after
detecting the completed transfer and prior to
updating the SSPBUF contents. Verify the WCOL
bit is clear after writing SSPBUF. If the WCOL is
set, clear the bit in software and rewrite the
SSPBUF register.
Date Codes that pertain to this issue:
All engineering and production devices.
With the ECCP configured for Half-Bridge PWM
mode (CCP1M3:0 = 0b1110), the output may be
corrupted for particular duty cycle selections.
Affected duty cycle values are 0 though 3, and
every subsequent increment of 4 (i.e., 7, 11, 15,
19, etc.).
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
Capture/Compare/PWM (ECCP)
OSC
/64 or
4. Module: Enhanced Universal
One bit has been added to the BAUDCON register
and one bit has been renamed. The added bit is
RXDTP and is in the location, BAUDCON<5>. The
renamed bit is the TXCKP bit (BAUDCON<4>),
which had been named SCKP.
The
(BAUDCON<5>) bits enable the TX and RX
signals to be inverted (polarity reversed).
Register 17-3, on page 194, will be changed as
shown on page 3.
Work around
None required.
Date Codes that pertain to this issue:
All engineering and production devices.
TXCKP
Synchronous Receiver
Transmitter (EUSART)
(BAUDCON<4>)
© 2007 Microchip Technology Inc.
and
RXDTP