PIC18LF2610-I/SP Microchip Technology, PIC18LF2610-I/SP Datasheet - Page 9
![IC MCU FLASH 32KX16 28SDIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC18LF2610-I/SP
Manufacturer Part Number
PIC18LF2610-I/SP
Description
IC MCU FLASH 32KX16 28SDIP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC18F2221-ISO.pdf
(46 pages)
2.PIC18LF2410-ISO.pdf
(376 pages)
3.PIC18LF2410-ISO.pdf
(8 pages)
4.PIC18F2515-ISO.pdf
(16 pages)
5.PIC18F2515-ISO.pdf
(6 pages)
6.PIC18F2515-ISO.pdf
(8 pages)
Specifications of PIC18LF2610-I/SP
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
25
Program Memory Size
64KB (32K x 16)
Program Memory Type
FLASH
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Processor Series
PIC18LF
Core
PIC
Data Bus Width
8 bit
Data Ram Size
3968 B
Interface Type
CCP, ECCP, EUSART, I2C, MSSP, SPI
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
25
Number Of Timers
1 x 8
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit
Data Rom Size
3968 B
Height
3.3 mm
Length
34.67 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2 V
Width
7.24 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
24. Module: EUSART
25. Module: EUSART
26. Module: EUSART
27. Module: EUSART
© 2007 Microchip Technology Inc.
The EUSART auto-baud feature may occasionally
measure the incoming baud rate incorrectly. The
rate of incorrect baud rate measurements will
depend on the frequency of the incoming
synchronization byte and the system clock
frequency.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode (SYNC = 1) with clock
polarity high (SCKP = 1), the EUSART transmits a
shorter than expected clock on the CK pin for bit 0.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode, EUSART baud rates using
SPBRG values of ‘0’ and ‘1’ may not function
correctly.
Work around
Use another baud rate configuration to generate
the desired baud rate.
Date Codes that pertain to this issue:
All engineering and production devices.
During an auto-baud operation, the TX pin is
tri-stated. Transceivers which do not provide a
pull-up on the TX signal may cause the bus to
become
additional bus activity.
Work around
Use pull-up resistor on TX pin.
Date Codes that pertain to this issue:
All engineering and production devices.
inadvertently
active
and
PIC18F2515/2610/4515/4610
prevent
28. Module: MSSP
29. Module: MSSP
30. Module: MSSP
In an I
unaddressed slave may respond to bus activity
when data on the bus matches its address. The
first occurrence will set the BF bit. The second
occurrence will set the BF and the SSPOV bits. In
both situations, the SSPIF bit is not set and an
interrupt will not occur.
Work around
The I
I
Date Codes that pertain to this issue:
All engineering and production devices.
In I
work correctly.
Work around
Use a BRG value greater than ‘0’ by setting
SSPADD ≥ ‘1’.
Date Codes that pertain to this issue:
All engineering and production devices.
In I
ware to begin data reception and cleared by the
peripheral after a byte is received. After a byte is
received, the device may delay clearing RCEN.
Work around
Single byte receptions are typically not affected,
since the delay between byte receptions typically
is long enough for the RCEN bit to clear. For mul-
tiple byte receptions, the software must wait until
the bit is cleared before the next byte can be
received.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C event to maintain normal operation.
2
2
C Master mode, the BRG value of ‘0’ may not
C Master mode, the RCEN bit is set by soft-
2
C slave must clear the SSPOV bit after each
2
C system with multiple slave nodes, an
DS80199E-page 9