PIC18F4220-I/PT Microchip Technology, PIC18F4220-I/PT Datasheet - Page 145

• Manufacturer Part Number: PIC18F4220-I/PT
• Description: IC MCU FLASH 2KX16 A/D 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4220-I/PT

• Core Size: 8-Bit
• Program Memory Size: 4KB (2K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Core: PIC
• Processor Series: PIC18F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 512 B
• Data Rom Size: 256 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 36
• Number Of Timers: 2 x 8 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 13
• Height: 1 mm
• Interface Type: SPI, I2C, USART
• Length: 10 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC164305 - MODULE SKT FOR PM3 44TQFP444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / Rohs Status: Details

16.4
The Enhanced PWM mode provides additional PWM
output options for a broader range of control applica-
tions. The module is an upwardly compatible version of
the standard CCP module and offers up to four outputs,
designated P1A through P1D. Users are also able to
select the polarity of the signal (either active-high or
active-low). The module’s output mode and polarity are
configured
CCP1M3:CCP1M0 bits of the CCP1CON register
(CCP1CON<7:6> and CCP1CON<3:0>, respectively).
Figure 16-1 shows a simplified block diagram of PWM
operation. All control registers are double-buffered and
are loaded at the beginning of a new PWM cycle (the
period boundary when Timer2 resets) in order to pre-
vent glitches on any of the outputs. The exception is the
PWM Delay register, ECCP1DEL, which is loaded at
either the duty cycle boundary or the boundary period
(whichever comes first). Because of the buffering, the
module waits until the assigned timer resets instead of
starting immediately. This means that enhanced PWM
FIGURE 16-1:
© 2007 Microchip Technology Inc.
Note: The 8-bit timer TMR2 register is concatenated with the 2-bit internal Q clock or 2 bits of the prescaler to create the 10-bit time base.
CCPR1H (Slave)
Duty Cycle Registers
Enhanced PWM Mode
Comparator
CCPR1L
PR2
TMR2
by
Comparator
setting
(Note 1)
Clear Timer,
set CCP1 pin and
latch D.C.
SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODULE
CCP1CON<5:4>
the
P1M1:P1M0
R
S
PIC18F2220/2320/4220/4320
P1M1<1:0>
Q
and
PWM1CON
Controller
Output
2
CCP1/P1A
waveforms do not exactly match the standard PWM
waveforms but are instead offset by one full instruction
cycle (4 T
As before, the user must manually configure the
appropriate TRISD bits for output.
16.4.1
The P1M1:P1M0 bits in the CCP1CON register allow
one of four configurations:
• Single Output
• Half-Bridge Output
• Full-Bridge Output, Forward mode
• Full-Bridge Output, Reverse mode
The Single Output mode is the Standard PWM mode
discussed in Section 15.5 “PWM Mode”. The Half-
Bridge and Full-Bridge Output modes are covered in
detail in the sections that follow.
The general relationship of the outputs in all
configurations is summarized in Figure 16-2.
P1C
P1D
P1B
CCP1M<3:0>
4
OSC
TRISD<2>
TRISD<5>
TRISD<6>
TRISD<7>
PWM OUTPUT CONFIGURATIONS
).
RC2/CCP1/P1A
RD5/PSP5/P1B
RD6/PSP6/P1C
RD7/PSP7/P1D
DS39599G-page 143