PIC32MX460F512L-80I/PT Microchip Technology, PIC32MX460F512L-80I/PT Datasheet - Page 4

• Manufacturer Part Number: PIC32MX460F512L-80I/PT
• Description: IC PIC MCU FLASH 512K 100-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX460F512L-80I/PT

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-TFQFP
• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: I²C, IrDA, LIN, PMP, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC32MX4xx
• Core: MIPS
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: I2C , SPI , UART
• Maximum Clock Frequency: 80 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 5 x 16 bit, 1 x 32 bit
• Operating Supply Voltage: 2.3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM320003, DM320002, MA320002
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: PIC32
• No. Of I/o's: 85
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• No. Of Timers: 6
• Embedded Interface Type: EUART, I2C, PSP, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1000 - PIC32 BREAKOUT BOARDAC244003 - TEST BD MPLAB REAL ICE LOOPBACKDM320003 - BOARD DEMO USB PIC32 OTGAC244006 - KIT MPLAB REAL ICE TRACEAC164333 - MODULE SKT FOR PM3 100QFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC32MX3XX/4XX
TABLE 2:
DS80440D-page 4
Note 1:
Oscillator
Oscillator
Compare
Compare
Compare
Prefetch
Program
Memory
Module
Timers
Output
Output
Output
Cache
UART
UART
Flash
ADC
ADC
DMA
USB
USB
USB
USB
USB
SPI
Only those issues indicated in the last column apply to the current silicon revision.
Signal Source
Programming
5V Tolerance
CRC Append
Clock Switch
Clock Switch
Fault Mode
SILICON ISSUE SUMMARY (CONTINUED)
Transition
Operation
Detection
Feature
Clock
Mode
SE0
—
—
—
—
—
—
—
—
—
—
Number
Item
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
Enabling the primary programming/debug port (PGC1/
PGD1) on 64 lead variants disables the external and
internal references for the ADC, making the ADC
unusable.
Firmware clock switch requests to switch from FRC mode,
after a FSCM event, may fail.
The D+ and D– pins are not 5V tolerant.
The single-ended comparator detects SE0 transitions at a
voltage higher than the USB specification.
If the Predictive Prefetch Cache Enable bits
(PREFEN<1:0>) in the CHECON register are non-zero,
improper processor behavior may occur during a rare
boundary condition.
NVM registers must not be written immediately after a
programming operation is complete.
When the ADC is in operation, the current channel is
shorted to V
after sampling.
Writes to the timer registers PRx and TIMERx through the
Set/Clear/Invert registers corrupts the data written.
The USB clock does not automatically suspend when
entering Sleep mode.
The TRMT bit is asserted before the transmission is
complete.
PWM fault override is not asynchronous.
The SPIBUSY and SRMT bits assert 1 bit time before the
end of the transaction.
Faults may be cleared erroneously due to an aborted
read.
The TOKBUSY bit does not correctly indicate status when
a transfer completes within the Start of Frame (SOF)
threshold.
The interval between the first two SOF packets generated
does not meet USB specification.
If firmware clears a PWM Fault while a Fault condition is
asserted, an interrupt will not be generated for the current
Fault.
Clock switching and Two-Speed Start-up may cause a
general exception when the reserved bit 8 of the DDPCON
register is ‘0’.
The RXDA bit does not correctly reflect the RX FIFO
status after an overrun event.
In Pattern Match mode, the DMA module may not append
all of the CRC results to the result buffer.
REF
during the conversion period (12 T
Issue Summary
© 2010 Microchip Technology Inc.
AD
)
B2 B3 B4 B6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Revisions
Affected
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
(1)
X
X
X
X
X
X
X
X
X
X
X
X
X
X