PIC18C858-I/L Microchip Technology, PIC18C858-I/L Datasheet - Page 257

• Manufacturer Part Number: PIC18C858-I/L
• Description: IC PIC MCU OTP 16KX16 84PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C858-I/L

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Number Of I /o: 68
• Program Memory Type: OTP
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 84-PLCC
• Controller Family/series: PIC18
• No. Of I/o's: 68
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: 3-Wire, I2C, SPI, USART, CAN
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 68
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163007, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164310 - MODULE SKT FOR PM3 84PLCCDVA18XL840 - ADAPTER DEVICE ICE 84PLCCAC174012 - MODULE SKT PROMATEII 84PLCC
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C858I/L

22.3
Power-down mode is entered by executing a SLEEP
instruction.
Upon entering into Power-down mode, the following
actions are performed:
1.
2.
3.
4.
5.
To achieve lowest current consumption, follow these
steps before switching to Power-down mode:
1.
2.
3.
4.
5.
The MCLR pin must be at a logic high level (V
22.3.1
The device can wake-up from SLEEP through one of
the following events:
1.
2.
3.
2000 Microchip Technology Inc.
Watchdog Timer is cleared and kept running.
PD bit in RCON register is cleared.
TO bit in RCON register is set.
Oscillator driver is turned off.
I/O ports maintain the status they had before the
SLEEP instruction was executed.
Place all I/O pins at either V
ensure no external circuitry is drawing current
from I/O pin.
Power-down A/D and external clocks.
Pull all hi-impedance inputs to high or low
externally.
Place T0CKI at V
Current
pull-ups should be taken into account and dis-
abled if necessary.
External RESET input on MCLR pin.
Watchdog Timer Wake-up (if WDT was
enabled).
Interrupt from INT pin, RB port change or a
Peripheral Interrupt.
Power-down Mode (SLEEP)
WAKE-UP FROM SLEEP
consumption
SS
or V
DD
by
.
PORTB
DD
or V
Advanced Information
SS
on-chip
IHMC
and
).
The following peripheral interrupts can wake the device
from SLEEP:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Activity on CAN bus receive line.
Other peripherals cannot generate interrupts, since
during SLEEP, no on-chip clocks are present.
External MCLR Reset will cause a device RESET. All
other events are considered a continuation of program
execution and will cause a "wake-up". The TO and PD
bits in the RCON register can be used to determine the
cause of the device RESET. The PD bit, which is set on
power-up, is cleared when SLEEP is invoked. The TO
bit is cleared, if a WDT time-out occurred (and caused
wake-up).
When the SLEEP instruction is being executed, the next
instruction (PC + 2) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up is
regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction and then branches to the inter-
rupt address. In cases where the execution of the
instruction following SLEEP is not desirable, the user
should have a NOP after the SLEEP instruction.
PSP read or write.
TMR1 interrupt. Timer1 must be operating as
an asynchronous counter.
TMR3 interrupt. Timer3 must be operating as
an asynchronous counter.
CCP Capture mode interrupt.
Special event trigger (Timer1 in Asynchronous
mode using an external clock).
MSSP (START/STOP) bit detect interrupt.
MSSP transmit or receive in Slave mode
(SPI/I
USART RX or TX (Synchronous Slave mode).
A/D conversion (when A/D clock source is RC).
2
C).
PIC18CXX8
DS30475A-page 257