PIC18C858-I/L Microchip Technology, PIC18C858-I/L Datasheet - Page 12

• Manufacturer Part Number: PIC18C858-I/L
• Description: IC PIC MCU OTP 16KX16 84PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C858-I/L

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Number Of I /o: 68
• Program Memory Type: OTP
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 84-PLCC
• Controller Family/series: PIC18
• No. Of I/o's: 68
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: 3-Wire, I2C, SPI, USART, CAN
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 68
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163007, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164310 - MODULE SKT FOR PM3 84PLCCDVA18XL840 - ADAPTER DEVICE ICE 84PLCCAC174012 - MODULE SKT PROMATEII 84PLCC
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C858I/L

PIC18C658/858
6. Module: Interrupts
REGISTER 7-1:
FIGURE 1:
DS80084M-page 12
The operation of the GIE/GIEH bit (INTCON<7>) is
clarified as follows: when the bit is cleared, all
interrupts are disabled. This is regardless of the
state of the IPEN bit (RCON<7>), the priority of the
interrupt, or whether or not the interrupt is
unmasked. This varies from the original descrip-
tion, in which clearing the bit when IPEN = 1 would
only disable high priority interrupts.
The seventh paragraph in Section 7.0 of the
Device Data Sheet (beginning “When an interrupt
is responded to....”) is amended by adding the
following sentence to the end:
Low Priority Interrupt Generation
Peripheral Interrupt Enable bit
Peripheral Interrupt Priority bit
Peripheral Interrupt Flag bit
bit 7
TMR1IF
TMR1IE
TMR1IP
XXXXIE
XXXXIP
XXXXIF
INTERRUPT LOGIC (EXCERPT)
INTCON REGISTER (EXCERPT)
GIE/GIEH: Global Interrupt Enable bit
When IPEN (RCON<7>) = 0:
1 = Enables all unmasked interrupts
0 = Disables all interrupts
When IPEN (RCON<7>) = 1:
1 = Enables all high priority interrupts
0 = Disables all interrupts
Additional Peripheral Interrupts
TMR0IE
TMR0IP
TMR0IF
INT1IF
INT1IE
INT1IP
INT2IF
INT2IE
INT2IP
RBIF
RBIE
RBIP
“It is important to note, however, that clearing the
GIE/GIEH bit, regardless of the state of the IPEN
bit, will disable all interrupts.”
The changes to the bit descriptions in Register 7-1
in the Device Data Sheet are shown in the excerpt
below (changes in bold).
Also, the interrupt logic funnel shown in Figure 7-1
of the Device Data Sheet is amended with the
addition of a GIE/GIEH control line, as shown in
Figure 1 (new material in bold line).
 2003 Microchip Technology Inc.
GIEL/PEIE
GIE/GEIH
Interrupt to CPU
Vector to Location
0018h