PIC18F6720-I/PT Microchip Technology, PIC18F6720-I/PT Datasheet - Page 22

• Manufacturer Part Number: PIC18F6720-I/PT
• Description: IC MCU FLASH 64KX16 EE 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6720-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Eeprom Size: 1K x 8
• Ram Size: 3.75K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.75 KB
• Interface Type: I2C/SPI/USART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18FXX20
4.3
A configuration address may be read and output on
SDATA via the 4-bit command, ‘1001’. Configuration
data is read and written in a byte-wise fashion, so it is
not necessary to merge two bytes into a word prior to a
compare. The result may then be immediately
compared to the appropriate configuration data in the
programmer’s memory for verification. Refer to
Section 4.1 for implementation details of reading
configuration data.
4.4
Data EEPROM is accessed one byte at a time via an
Address Pointer (register pair EEADR:EEADRH) and a
data latch (EEDATA). Data EEPROM is read by loading
EEADR:EEADRH with the desired memory location
and initiating a memory read by appropriately
configuring the EECON1 register. The data will be
loaded into EEDATA, where it may be serially output on
SDATA via the 4-bit command, ‘0010’ (Shift Out Data
Holding register). A delay of P6 must be introduced
after the falling edge of the 8th SCLK of the operand to
allow SDATA to transition from an input to an output.
During this time, SCLK must be held low (see
Figure 4-4).
The command sequence to read a single byte of data
is shown in Figure 4-2.
DS39583C-page 22
Verify Configuration Bits
Read Data EEPROM Memory
FIGURE 4-3:
No
Move to TABLAT
READ DATA EEPROM
FLOW
Shift Out Data
 2010 Microchip Technology Inc.
Address
Read
Done
Byte
Start
Done
Set
?
Yes