ATMEGA2560V-8CU Atmel, ATMEGA2560V-8CU Datasheet - Page 161

• Manufacturer Part Number: ATMEGA2560V-8CU
• Description: IC MCU AVR 256K FLASH 100-CBGA
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA2560V-8CU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 256KB (128K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Operating Supply Voltage: 1.8 V to 5.5 V
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100PATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16.11.9
2549M–AVR–09/10
TCCR1C – Timer/Counter 1 Control Register C
• Bit 6 – ICESn: Input Capture Edge Select
This bit selects which edge on the Input Capture Pin (ICPn) that is used to trigger a capture
event. When the ICESn bit is written to zero, a falling (negative) edge is used as trigger, and
when the ICESn bit is written to one, a rising (positive) edge will trigger the capture.
When a capture is triggered according to the ICESn setting, the counter value is copied into the
Input Capture Register (ICRn). The event will also set the Input Capture Flag (ICFn), and this
can be used to cause an Input Capture Interrupt, if this interrupt is enabled.
When the ICRn is used as TOP value (see description of the WGMn3:0 bits located in the
TCCRnA and the TCCRnB Register), the ICPn is disconnected and consequently the input cap-
ture function is disabled.
• Bit 5 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be
written to zero when TCCRnB is written.
• Bit 4:3 – WGMn3:2: Waveform Generation Mode
See TCCRnA Register description.
• Bit 2:0 – CSn2:0: Clock Select
The three clock select bits select the clock source to be used by the Timer/Counter, see
16-10 on page 156
Table 16-6.
If external pin modes are used for the Timer/Countern, transitions on the Tn pin will clock the
counter even if the pin is configured as an output. This feature allows software control of the
counting.
Bit
(0x82)
Read/Write
Initial Value
CSn2
0
0
0
0
1
1
1
1
CSn1
0
0
1
1
0
0
1
1
Clock Select Bit Description
FOC1A
W
7
0
and
CSn0
Figure 16-11 on page
FOC1B
0
1
0
1
0
1
0
1
W
6
0
ATmega640/1280/1281/2560/2561
FOC1C
W
5
0
External clock source on Tn pin. Clock on falling edge
External clock source on Tn pin. Clock on rising edge
No clock source. (Timer/Counter stopped)
R
4
–
0
156.
clk
clk
clk
clk
I/O
clk
R
I/O
3
–
0
I/O
I/O
/1024 (From prescaler)
/256 (From prescaler)
I/O
/64 (From prescaler)
/8 (From prescaler)
Description
/1 (No prescaling
R
2
–
0
R
1
0
–
R
0
–
0
TCCR1C
Figure
161