ADUC7024BSTZ62 Analog Devices Inc, ADUC7024BSTZ62 Datasheet - Page 81

• Manufacturer Part Number: ADUC7024BSTZ62
• Description: IC MCU FLASH 62K ANLG I/O 64LQFP
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7024BSTZ62

• Core Size: 16/32-Bit
• Program Memory Size: 62KB (62K x 8)
• Design Resources: Sensing Low-g Acceleration Using ADXL345 Digital Accelerometer Connected to ADuC7024 (CN0133)
• Core Processor: ARM7
• Speed: 44MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: PLA, PWM, PSM, Temp Sensor, WDT
• Number Of I /o: 30
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 10x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-LQFP
• Controller Family/series: (ARM7) ADUC
• No. Of I/o's: 30
• Ram Memory Size: 8KB
• Cpu Speed: 44MHz
• No. Of Timers: 4
• Digital Ic Case Style: LQFP
• Embedded Interface Type: I2C, SPI, UART
• Rohs Compliant: Yes
• Package: 64LQFP
• Device Core: ARM7TDMI
• Family Name: ADuC7xxx
• Maximum Speed: 44 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 30
• Interface Type: I2C/SPI/UART
• On-chip Adc: 10-chx12-bit
• On-chip Dac: 2-chx12-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

XMCFG Register
Name
XMCFG
XMCFG is set to 1 to enable external memory access. This must
be set to 1 before any port pins function as external memory
access pins. The port pins must also be individually enabled via
the GPxCON MMR.
XMxCON Registers
Name
XM0CON
XM1CON
XM2CON
XM3CON
XMxCON are the control registers for each memory region.
They allow the enabling/disabling of a memory region and
control the data bus width of the memory region.
Table 81. XMxCON MMR Bit Descriptions
Bit
1
0
XMxPAR Registers
Name
XM0PAR
XM1PAR
XM2PAR
XM3PAR
Description
Selects Data Bus Width. Set by the user to select a 16-bit
data bus. Cleared by the user to select an 8-bit data bus.
Enables Memory Region. Set by the user to enable memory
region. Cleared by the user to disable the memory region.
Address
0xFFFFF000
Address
0xFFFFF010
0xFFFFF014
0xFFFFF018
0xFFFFF01C
Address
0xFFFFF020
0xFFFFF024
0xFFFFF028
0xFFFFF02C
Default Value
0x00
Default Value
0x00
0x00
0x00
0x00
Default Value
0x70FF
0x70FF
0x70FF
0x70FF
Access
R/W
Access
R/W
R/W
R/W
R/W
Access
R/W
R/W
R/W
R/W
Rev. B | Page 81 of 92
XMxPAR are registers that define the protocol used for
accessing the external memory for each memory region.
Table 82. XMxPAR MMR Bit Descriptions
Bit
15
14:12
11
10
9
8
7:4
3:0
Figure 70, Figure 71, Figure 72, and Figure 73 show the timing
for a read cycle, a read cycle with address hold and bus turn
cycles, a write cycle with address and write hold cycles, and a
write cycle with wait sates, respectively.
ADuC7019/20/21/22/24/25/26/27/28
Description
Enable Byte Write Strobe. This bit is only used for two,
8-bit memory sharing the same memory region. Set by
the user to gate the A0 output with the WS output. This
allows byte write capability without using BHE and BLE
signals. Cleared by user to use BHE and BLE signals.
Number of Wait States on the Address Latch Enable Strobe.
Reserved.
Extra Address Hold Time. Set by the user to disable extra
hold time. Cleared by the user to enable one clock cycle
of hold on the address in read and write.
Extra Bus Transition Time on Read. Set by the user to disable
extra bus transition time. Cleared by the user to enable
one extra clock before and after the read strobe (RS).
Extra Bus Transition Time on Write. Set by the user to disable
extra bus transition time. Cleared by the user to enable
one extra clock before and after the write strobe (WS).
Number of Write Wait States. Select the number of wait
states added to the length of the WS pulse. 0x0 is 1 clock;
0xF is 16 clock cycles (default value).
Number of Read Wait States. Select the number of wait
states added to the length of the RS pulse. 0x0 is 1 clock;
0xF is 16 clock cycles (default value).