LPC2388FBD144,551 NXP Semiconductors, LPC2388FBD144,551 Datasheet - Page 64

• Manufacturer Part Number: LPC2388FBD144,551
• Description: IC ARM7 MCU FLASH 512K 144LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2300r

Specifications of LPC2388FBD144,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 144-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 104
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC23
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/SPI/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 104
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB2388, MCB2388U, MCB2388UME
• Development Tools By Supplier: OM11012
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: OM11012 - BOARD EVAL FOR LPC2388568-3999 - BOARD EVAL FOR LPC23 ARM MCU622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4323; 935285417551; LPC2388FBD144-S

NXP Semiconductors
LPC2388
Product data sheet
14.4 XTAL and RTCX Printed Circuit Board (PCB) layout guidelines
14.5 Standard I/O pin configuration
The crystal should be connected on the PCB as close as possible to the oscillator input
and output pins of the chip. Take care that the load capacitors C
third overtone crystal usage have a common ground plane. The external components
must also be connected to the ground plain. Loops must be made as small as possible in
order to keep the noise coupled in via the PCB as small as possible. Also parasitics
should stay as small as possible. Values of C
accordingly to the increase in parasitics of the PCB layout.
Figure 28
The default configuration for standard I/O pins is input with pull-up enabled. The weak
MOS devices provide a drive capability equivalent to pull-up and pull-down resistors.
Fig 28. Standard I/O pin configuration with analog input
•
•
•
•
•
as digital output
as analog input
as digital input
pin configured
pin configured
pin configured
Digital output driver: Open-drain mode enabled/disabled
Digital input: Pull-up enabled/disabled
Digital input: Pull-down enabled/disabled
Digital input: Repeater mode enabled/disabled
Analog input
driver
shows the possible pin modes for standard I/O pins with analog input function:
All information provided in this document is subject to legal disclaimers.
analog input
data input
Rev. 2 — 13 July 2010
output
output enable
pull-down enable
pull-up enable
select analog input
x1
Single-chip 16-bit/32-bit microcontroller
and C
x2
should be chosen smaller
V
DD
weak
pull-up
weak
pull-down
x1
, C
x2
, and C
LPC2388
© NXP B.V. 2010. All rights reserved.
V
ESD
DD
ESD
V
SS
x3
in case of
002aaf496
64 of 72
PIN