ST72F264G1M6 STMicroelectronics, ST72F264G1M6 Datasheet - Page 113

• Manufacturer Part Number: ST72F264G1M6
• Description: IC MCU 8BIT 4K 28 SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F264G1M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: ST72F2x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7F264-IND/USB, ST72F34X-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• For Use With: 497-6423 - BOARD EVAL BASED ON ST72264G1497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2105-5

I
I
Read / Write
Reset Value: 0000 0000 (00h)
Bit 7 = FM/SM Fast/Standard I
This bit is set and cleared by software. It is not
cleared when the interface is disabled (PE=0).
0: Standard I
1: Fast I
Bit 6:0 = CC[6:0] 7-bit clock divider.
These bits select the speed of the bus (F
pending on the I
when the interface is disabled (PE=0).
Refer to the Electrical Characteristics section for
the table of values.
Note: The programmed F
SCL and SDA lines.
FM/SM
2
2
C BUS INTERFACE (Cont’d)
C CLOCK CONTROL REGISTER (CCR)
7
CC6
2
C mode
2
CC5
C mode
2
C mode. They are not cleared
CC4
SCL
CC3
assumes no load on
2
C mode.
CC2
CC1
SCL
CC0
) de-
0
I
Read / Write
Reset Value: 0000 0000 (00h)
Bit 7:0 = D[7:0] 8-bit Data Register.
These bits contain the byte to be received or trans-
mitted on the bus.
– Transmitter mode: Byte transmission start auto-
– Receiver mode: the first data byte is received au-
2
C DATA REGISTER (DR)
matically when the software writes in the DR reg-
ister.
tomatically in the DR register using the least sig-
nificant bit of the address.
Then, the following data bytes are received one
by one after reading the DR register.
D7
7
ST72260Gx, ST72262Gx, ST72264Gx
D6
D5
D4
D3
D2
D1
113/172
D0
0