STM32F103C4T6A STMicroelectronics, STM32F103C4T6A Datasheet - Page 32

• Manufacturer Part Number: STM32F103C4T6A
• Description: MCU ARM 32BIT 16K FLASH 48-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C4T6A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8316

Electrical characteristics
5.3
5.3.1
32/87
Table 7.
1. All main power (V
2. Negative injection disturbs the analog performance of the device. See note in
3. Positive injection is not possible on these I/Os. A negative injection is induced by V
4.
5. When several inputs are submitted to a current injection, the maximum ΣI
Table 8.
Operating conditions
General operating conditions
Table 9.
Symbol
V
supply, in the permitted range.
characteristics.
never be exceeded. Refer to
values.
never be exceeded. Refer to
values.
positive and negative injected currents (instantaneous values).
f
f
I
A positive injection is induced by V
f
PCLK1
PCLK2
ΣI
V
DDA
INJ(PIN)
HCLK
Symbol
V
BAT
DD
INJ(PIN)
Symbol
I
I
VDD
VSS
I
T
IO
(1)
STG
T
J
(2)
Current characteristics
Thermal characteristics
General operating conditions
Internal AHB clock frequency
Internal APB1 clock frequency
Internal APB2 clock frequency
Standard operating voltage
Analog operating voltage
(ADC not used)
Analog operating voltage
(ADC used)
Backup operating voltage
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on five volt tolerant pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
, V
Storage temperature range
Maximum junction temperature
DDA
Parameter
) and ground (V
Table 6: Voltage characteristics
Table 6: Voltage characteristics
Doc ID 15060 Rev 5
IN
>V
DD
DD
SS
/V
Ratings
SS
while a negative injection is induced by V
DDA
ground lines (sink)
, V
Ratings
SSA
power lines (source)
Must be the same potential
as V
) pins must always be connected to the external power
(4)
DD
(2)
Conditions
for the maximum allowed input voltage
for the maximum allowed input voltage
(3)
(1)
(1)
STM32F103x4, STM32F103x6
INJ(PIN)
(5)
Section 5.3.18: 12-bit ADC
–65 to +150
is the absolute sum of the
IN
Value
IN
150
Min
<V
2.4
1.8
0
0
0
2
2
<V
SS
SS
-5/+0
. I
Max.
− 25
± 25
150
150
± 5
25
. I
INJ(PIN)
INJ(PIN)
Max
3.6
3.6
3.6
3.6
72
36
72
must
must
Unit
Unit
MHz
°C
°C
Unit
mA
V
V
V