STM32F103C4T6A STMicroelectronics, STM32F103C4T6A Datasheet - Page 35

• Manufacturer Part Number: STM32F103C4T6A
• Description: MCU ARM 32BIT 16K FLASH 48-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C4T6A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8316

STM32F103x4, STM32F103x6
5.3.4
5.3.5
Embedded reference voltage
The parameters given in
temperature and V
Table 12.
1. Shortest sampling time can be determined in the application by multiple iterations.
2. Guaranteed by design, not tested in production.
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in
measurement
All Run-mode current consumption measurements given in this section are performed with a
reduced code that gives a consumption equivalent to Dhrystone 2.1 code.
Maximum current consumption
The MCU is placed under the following conditions:
●
●
●
●
●
The parameters given in
under ambient temperature and V
T
V
Symbol
V
S_vrefint
T
RERINT
REFINT
Coeff
All I/O pins are in input mode with a static value at V
All peripherals are disabled except when explicitly mentioned
The Flash memory access time is adjusted to the f
to 24 MHz, 1 wait state from 24 to 48 MHz and 2 wait states above)
Prefetch in ON (reminder: this bit must be set before clock setting and bus prescaling)
When the peripherals are enabled f
(2)
(2)
(1)
Internal reference voltage
ADC sampling time when
reading the internal reference
voltage
Internal reference voltage
spread over the temperature
range
Temperature coefficient
Embedded internal reference voltage
scheme.
DD
Parameter
supply voltage conditions summarized in
Table 12
Table
Doc ID 15060 Rev 5
13,
DD
are derived from tests performed under ambient
Table 14
supply voltage conditions summarized in
PCLK1
–40 °C < T
–40 °C < T
V
and
DD
Conditions
= f
= 3 V ±10 mV
Table 15
HCLK
A
A
< +105 °C
< +85 °C
/2, f
Figure 12: Current consumption
HCLK
DD
are derived from tests performed
PCLK2
or V
frequency (0 wait state from 0
Table
1.16
1.16
Min
= f
SS
Electrical characteristics
HCLK
(no load)
9.
1.20
1.20
Typ
5.1
17.1
1.26
1.24
Max
100
10
Table
(2)
ppm/°C
9.
Unit
mV
µs
V
V
35/87