MC908JL3ECPE Freescale Semiconductor, MC908JL3ECPE Datasheet - Page 35

• Manufacturer Part Number: MC908JL3ECPE
• Description: IC MCU 4K FLASH 8MHZ 28-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JL3ECPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 23
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.3 V
• Data Converters: A/D 12x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.600", 15.24mm)
• Controller Family/series: HC08
• No. Of I/o's: 23
• Ram Memory Size: 128Byte
• Cpu Speed: 8MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Chapter 3
Configuration Registers (CONFIG)
3.1 Introduction
This section describes the configuration registers (CONFIG1 and CONFIG2). The configuration registers
enables or disables the following options:
3.2 Functional Description
The configuration register is used in the initialization of various options. The configuration register can be
written once after each reset. All of the configuration register bits are cleared during reset. Since the
various options affect the operation of the MCU it is recommended that this register be written immediately
after reset. The configuration register is located at $001E and $001F, and may be read at anytime.
3.3 Configuration Register 1 (CONFIG1)
COPRS — COP reset period selection bit
Freescale Semiconductor
•
•
•
•
•
•
1 = COP reset cycle is 8176 × 2OSCOUT
0 = COP reset cycle is 262,128 × 2OSCOUT
Stop mode recovery time (32 × 2OSCOUT cycles or 4096 × 2OSCOUT cycles)
STOP instruction
Computer operating properly module (COP)
COP reset period (COPRS), 8176 × 2OSCOUT or 262,128 × 2OSCOUT
Enable LVI circuit
Select LVI trip voltage
Address:
The CONFIG registers are one-time writable by the user after each reset.
Upon a reset, the CONFIG registers default to predetermined settings as
shown in
Reset:
Read:
Write:
COPRS
$001F
Bit 7
Figure 3-1
R
0
Figure 3-1. Configuration Register 1 (CONFIG1)
= Reserved
MC68HC908JL3E Family Data Sheet, Rev. 4
R
6
0
and
Figure
R
5
0
3-2.
NOTE
LVID
4
0
R
3
0
SSREC
2
0
STOP
1
0
COPD
Bit 0
0
35