C8051F411-GM Silicon Laboratories Inc, C8051F411-GM Datasheet - Page 151

• Manufacturer Part Number: C8051F411-GM
• Description: IC 8051 MCU 32K FLASH 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F41xr

Specifications of C8051F411-GM

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 20
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.25 V
• Data Converters: A/D 20x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F4x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2368 B
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 20
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F410DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 20 Channel
• On-chip Dac: 12 bit, 2 Channel
• No. Of I/o's: 20
• Ram Memory Size: 2368Byte
• Cpu Speed: 50MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1454 - ADAPTER PROGRAM TOOLSTICK F411336-1317 - KIT EVAL FOR C8051F411336-1314 - KIT DEV FOR C8051F41X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1309

18.2. Port I/O Initialization
Port I/O initialization consists of the following steps:
All Port pins must be configured as either analog or digital inputs. Any pins to be used as Comparator or
ADC inputs should be configured as an analog inputs. When a pin is configured as an analog input, its
weak pullup, digital driver, and digital receiver are disabled. This process saves power and reduces noise
on the analog input. Pins configured as digital inputs may still be used by analog peripherals; however, this
practice is not recommended.
Additionally, all analog input pins should be configured to be skipped by the Crossbar (accomplished by
setting the associated bits in PnSKIP). Port input mode is set in the PnMDIN register, where a ‘1’ indicates
a digital input, and a ‘0’ indicates an analog input. All port pins in analog mode must have a '1' set in the
corresponding Port Latch register. All pins default to digital inputs on reset. See SFR Definition 18.4 for the
PnMDIN register details.
Important Note: Port 0 pins are 5 V tolerant across the operating range of V
input current range of P0 pins when overdriven above V
drive modes for Port 0: Normal and High-Impedance. When the corresponding bit in P0ODEN is logic 0,
Normal Overdrive Mode is selected and the port pin requires 150 µA peak overdrive current when its volt-
age reaches approximately V
ance Overdrive Mode is selected and the port pin does not require any additional overdrive current. Pins
configured to High-Impedance Overdrive Mode consume slightly more power from V
ured to Normal Overdrive Mode. Note that Port 1 and Port 2 pins cannot be overdriven above V
have the same behavior as P0 in Normal Mode.
Step 1. Select the input mode (analog or digital) for all Port pins, using the Port Input Mode
Step 2. Select the output mode (open-drain or push-pull) for all Port pins, using the Port Output
Step 3. Select any pins to be skipped by the I/O Crossbar using the Port Skip registers (PnSKIP).
Step 4. Assign Port pins to desired peripherals using the XBRn registers.
Step 5. Enable the Crossbar (XBARE = ‘1’).
register (PnMDIN). If the pin is in analog mode, a '1' must also be written to the
corresponding Port Latch.
Mode register (PnMDOUT).
IO
+ 0.7 V. When the corresponding bit in P0ODEN is logic 1, High-Imped-
Rev. 1.1
IO
(when V
IO
is 3.3 V nominal). There are two over-
C8051F410/1/2/3
IO
. Figure 18.5 shows the
IO
than pins config-
IO
and
151