AT89C51RB2-RLRIM Atmel, AT89C51RB2-RLRIM Datasheet - Page 29
![IC MCU FLASH 8051 16K 5V 44-VQFP](/photos/6/92/69202/313-44-vqfp_sml.jpg)
AT89C51RB2-RLRIM
Manufacturer Part Number
AT89C51RB2-RLRIM
Description
IC MCU FLASH 8051 16K 5V 44-VQFP
Manufacturer
Atmel
Series
89Cr
Datasheet
1.AT89C51RB2-RLTIL.pdf
(127 pages)
Specifications of AT89C51RB2-RLRIM
Core Processor
8051
Core Size
8-Bit
Speed
60MHz
Connectivity
SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
32
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
44-TQFP, 44-VQFP
For Use With
AT89STK-11 - KIT STARTER FOR AT89C51RX2
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Data Converters
-
Other names
AT89C51RB2RLRIMTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Registers
4180E–8051–10/06
Table 20. T2CON Register
T2CON – Timer 2 Control Register (C8h)
Reset Value = 0000 0000b
Bit addressable
Number
TF2
Bit
7
7
6
5
4
3
2
1
0
Mnemonic Description
CP/RL2#
EXEN2
EXF2
RCLK
C/T2#
EXF2
TCLK
TR2
TF2
Bit
6
Timer 2 Overflow Flag
Must be cleared by software.
Set by hardware on Timer 2 overflow, if RCLK = 0 and TCLK = 0.
Timer 2 External Flag
Set when a capture or a reload is caused by a negative transition on T2EX pin if
EXEN2 = 1.
When set, causes the CPU to vector to Timer 2 interrupt routine when Timer 2
interrupt is enabled.
Must be cleared by software. EXF2 doesn’t cause an interrupt in Up/down
counter mode (DCEN = 1).
Receive Clock Bit
Cleared to use timer 1 overflow as receive clock for serial port in mode 1 or 3.
Set to use Timer 2 overflow as receive clock for serial port in mode 1 or 3.
Transmit Clock Bit
Cleared to use timer 1 overflow as transmit clock for serial port in mode 1 or 3.
Set to use Timer 2 overflow as transmit clock for serial port in mode 1 or 3.
Timer 2 External Enable Bit
Cleared to ignore events on T2EX pin for Timer 2 operation.
Set to cause a capture or reload when a negative transition on T2EX pin is
detected, if Timer 2 is not used to clock the serial port.
Timer 2 Run Control Bit
Cleared to turn off Timer 2.
Set to turn on Timer 2.
Timer/Counter 2 Select Bit
Cleared for timer operation (input from internal clock system: F
Set for counter operation (input from T2 input pin, falling edge trigger). Must be 0
for clock out mode.
Timer 2 Capture/Reload Bit
If RCLK = 1 or TCLK = 1, CP/RL2# is ignored and timer is forced to auto-reload
on Timer 2 overflow.
Cleared to auto-reload on Timer 2 overflows or negative transitions on T2EX pin
if EXEN2 = 1.
Set to capture on negative transitions on T2EX pin if EXEN2 = 1.
RCLK
5
TCLK
4
EXEN2
3
AT89C51RB2/RC2
TR2
2
C/T2#
1
CLK PERIPH
CP/RL2#
).
0
29