PIC18F2420-I/SP Microchip Technology, PIC18F2420-I/SP Datasheet - Page 26

• Manufacturer Part Number: PIC18F2420-I/SP
• Description: IC MCU FLASH 8KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2420-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI, I2C, USART
• Maximum Clock Frequency: 31 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Data Rom Size: 256 KB
• Height: 3.3 mm
• Length: 34.67 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 7.24 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2420/2520/4420/4520
TABLE 2-2:
DS39631E-page 24
Capacitor values are for design guidance only.
These capacitors were tested with the crystals listed
below for basic start-up and operation. These values
are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following this table for additional
information.
Osc Type
DD
Note 1: Higher capacitance increases the stability
HS
XT
LP
and temperature range for the application.
2: When operating below 3V V
3: Since each resonator/crystal has its own
4: Rs may be required to avoid overdriving
5: Always verify oscillator performance over
25 MHz
32 kHz
1 MHz
of the oscillator but also increases the
start-up time.
using certain ceramic resonators at any
voltage, it may be necessary to use the
HS mode or switch to a crystal oscillator.
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
components.
crystals with low drive level specification.
the V
expected for the application.
10 MHz
20 MHz
25 MHz
25 MHz
Crystal
32 kHz
1 MHz
4 MHz
4 MHz
Freq
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
DD
Crystals Used:
and temperature range that is
Typical Capacitor Values
values
30 pF
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
0 pF
C1
Tested:
10 MHz
20 MHz
4 MHz
of
DD
, or when
30 pF
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
5 pF
external
C2
An external clock source may also be connected to the
OSC1 pin in the HS mode, as shown in Figure 2-2.
FIGURE 2-2:
2.3
The EC and ECIO Oscillator modes require an external
clock source to be connected to the OSC1 pin. There is
no oscillator start-up time required after a Power-on
Reset or after an exit from Sleep mode.
In the EC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 2-3 shows the pin connections for the EC
Oscillator mode.
FIGURE 2-3:
The ECIO Oscillator mode functions like the EC mode,
except that the OSC2 pin becomes an additional gen-
eral purpose I/O pin. The I/O pin becomes bit 6 of
PORTA (RA6). Figure 2-4 shows the pin connections
for the ECIO Oscillator mode.
FIGURE 2-4:
Clock from
Ext. System
Clock from
Ext. System
Clock from
Ext. System
External Clock Input
F
RA6
Open
OSC
/4
EXTERNAL CLOCK INPUT
OPERATION (HS OSC
CONFIGURATION)
EXTERNAL CLOCK
INPUT OPERATION
(EC CONFIGURATION)
EXTERNAL CLOCK
INPUT OPERATION
(ECIO CONFIGURATION)
© 2008 Microchip Technology Inc.
OSC1/CLKI
I/O (OSC2)
OSC1/CLKI
OSC2/CLKO
OSC1
OSC2
PIC18FXXXX
PIC18FXXXX
PIC18FXXXX
(HS Mode)