PIC18LF2523-I/SP Microchip Technology, PIC18LF2523-I/SP Datasheet - Page 31

• Manufacturer Part Number: PIC18LF2523-I/SP
• Description: IC PIC MCU FLASH 16KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF2523-I/SP

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.0
© 2005 Microchip Technology Inc.
Standard Operating Conditions
Operating Temperature: 25°C is recommended
Param
P11A
P12
P13
P14
P15
P16
P17
P18
Note 1:
No.
2:
3:
T
T
T
T
T
T
T
T
AC/DC CHARACTERISTICS TIMING REQUIREMENTS
FOR PROGRAM/VERIFY TEST MODE (CONTINUED)
Sym
DRWT
HLD
SET
VALID
SET
DLY
HLD
HLD
Do not allow excess time when transitioning MCLR between V
executions to occur. The maximum transition time is:
where T
specific values, refer to the Electrical Characteristics section of the device data sheet for the particular device.
When ICPORT = 1, this specification also applies to ICV
At 0°C-50°C.
2 V
3 PGM ↑ Setup Time to MCLR/V
8 Delay between Last PGC ↓ and MCLR/V
2 Input Data Hold Time from MCLR/V
3 MCLR/V
4 MCLR/V
1 T
2 ms (for HS/PLL mode only) + 1.5 μs (for EC mode only)
Data Write Polling Time
Data Out Valid from PGC ↑
CY
DD
CY
+ T
↑ Setup Time to MCLR/V
is the instruction cycle time, T
PWRT
PP
PP
/RE3 ↓ to V
/RE3 ↓ to PGM ↓
(if enabled) + 1024 T
Characteristic
DD
↓
PP
PP
PIC18F2423/2523/4423/4523
/RE3 ↑
/RE3 ↑
OSC
PP
PWRT
/RE3 ↑
(for LP, HS, HS/PLL and XT modes only) +
PP
is the Power-up Timer period and T
/RE3 ↓
PP
.
Min
100
10
—
4
2
2
0
0
IL
and V
Max
IHH
100
—
—
—
—
—
—
—
; this can cause spurious program
Units
ms
μs
ns
ns
μs
ns
OSC
s
s
is the oscillator period. For
(Note 2)
(Note 2)
Conditions
DS39759A-page 31