ST72F324J4B5 STMicroelectronics, ST72F324J4B5 Datasheet - Page 38

• Manufacturer Part Number: ST72F324J4B5
• Description: MCU 8BIT 16K FLASH 5V 42DIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324J4B5

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -10°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7F521-IND/USB, ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 10 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-4848

ST72324Jx ST72324Kx
INTERRUPTS (Cont’d)
7.7 EXTERNAL INTERRUPT CONTROL REGISTER (EICR)
Read/Write
Reset Value: 0000 0000 (00h)
Bit 7:6 = IS1[1:0] ei2 and ei3 sensitivity
The interrupt sensitivity, defined using the IS1[1:0]
bits, is applied to the following external interrupts:
- ei2 (port B3..0)
- ei3 (port B4)
These 2 bits can be written only when I1 and I0 of
the CC register are both set to 1 (level 3).
Bit 5 = IPB Interrupt polarity for port B
This bit is used to invert the sensitivity of the port B
[3:0] external interrupts. It can be set and cleared
by software only when I1 and I0 of the CC register
are both set to 1 (level 3).
0: No sensitivity inversion
1: Sensitivity inversion
38/164
1
IS11 IS10
IS11 IS10
IS11
0
0
1
1
0
0
1
1
7
IS10
0
1
0
1
0
1
0
1
Falling edge only
Rising edge only
IPB
Falling edge &
IPB bit =0
low level
External Interrupt Sensitivity
External Interrupt Sensitivity
IS21
Falling edge & low level
Rising and falling edge
Rising and falling edge
Falling edge only
Rising edge only
IS20
IPA
Falling edge only
Rising edge only
Rising edge
& high level
IPB bit =1
0
0
0
Bit 4:3 = IS2[1:0] ei0 and ei1 sensitivity
The interrupt sensitivity, defined using the IS2[1:0]
bits, is applied to the following external interrupts:
- ei0 (port A3..0)
- ei1 (port F2..0)
These 2 bits can be written only when I1 and I0 of
the CC register are both set to 1 (level 3).
Bit 2 = IPA Interrupt polarity for port A
This bit is used to invert the sensitivity of the port A
[3:0] external interrupts. It can be set and cleared
by software only when I1 and I0 of the CC register
are both set to 1 (level 3).
0: No sensitivity inversion
1: Sensitivity inversion
Bits 1:0 = Reserved, must always be kept cleared.
IS21 IS20
IS21 IS20
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Falling edge only
Rising edge only
Falling edge &
IPA bit =0
low level
External Interrupt Sensitivity
External Interrupt Sensitivity
Falling edge & low level
Rising and falling edge
Rising and falling edge
Falling edge only
Rising edge only
Falling edge only
Rising edge only
Rising edge
& high level
IPA bit =1