M30624FGAFP#U5 Renesas Electronics America, M30624FGAFP#U5 Datasheet - Page 119
![IC M16C MCU FLASH 100QFP](/photos/12/31/123149/m30624fgafp_u5_sml.jpg)
M30624FGAFP#U5
Manufacturer Part Number
M30624FGAFP#U5
Description
IC M16C MCU FLASH 100QFP
Manufacturer
Renesas Electronics America
Series
M16C™ M16C/60r
Datasheets
1.M30622SAFPU5.pdf
(277 pages)
2.M30622SAFPU5.pdf
(617 pages)
3.M30622SAFPU5.pdf
(308 pages)
4.M30624FGAFPU5.pdf
(275 pages)
Specifications of M30624FGAFP#U5
Core Processor
M16C/60
Core Size
16-Bit
Speed
16MHz
Connectivity
SIO, UART/USART
Peripherals
DMA, PWM, WDT
Number Of I /o
85
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
20K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 10x10b, D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 85°C
Package / Case
100-QFP
Cpu Family
M16C
Device Core Size
16/32Bit
Frequency (max)
16MHz
Interface Type
SIM/UART
Total Internal Ram Size
20KB
# I/os (max)
87
Number Of Timers - General Purpose
11
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
4.2V
On-chip Adc
10-chx10-bit
On-chip Dac
2-chx8-bit
Instruction Set Architecture
CISC
Operating Temp Range
-20C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
100
Package Type
PQFP
For Use With
867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
M30624FGAFP#U5M30624FGAFP#D3
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30624FGAFP#U5M30624FGAFP#D5
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Serial I/O
116
Figure 1.16.9. Serial I/O-related registers (6)
UART2 special mode register 2 (I C bus exclusive use register)
UART2 special mode register 3 (I C bus exclusive use register)
b7 b6 b5 b4 b3 b2 b1 b0
b7 b6 b5 b4 b3 b2 b1 b0
Note 1: This bit can be read or written to when UART2 special mode register (U2SMR at address 0377
Note 2: These bits are initialized to “000” when SDDS = “0”, with the analog delay circuit selected. After a reset,
Note 3: When analog delay is selected, only the analog delay value is effective; when digital delay is selected,
Note 4: The amount of delay varies with the load on SCL and SDA pins. Also, when using an external clock, the
7 (SDDS: SDA digital delay select bit) = “1”. When the initial value of UART2 special mode register 3
(U2SMR3) is read after setting SDDS = “1”, the value is “00
register 3 (U2SMR3) after setting SDDS = “1”, be sure to write 0's to bits 0–4. When SDDS = “0”,
this register cannot be written to; when read, the value is indeterminate.
these bits are set to “000”, with the analog delay circuit selected. However, because these bits can be
read only when SDDS = “1”, the value read from these bits when SDDS = “0” is indeterminate.
only the digital delay value is effective.
amount of delay increases by about 100 ns, so be sure to take this into account when using the device.
ALS
SDHI
DL0
DL1
DL2
IICM2
CSC
SWC
STAC
SWC2
SHTC
symbol
symbol
Nothing is assigned.
In an attempt to write to these bits, write “0”. The value, if read, turns out to be
indeterminate. However, when SDDS = “1”, the value “0” is read out (Note 1)
Bit
Bit
Symbol
Symbol
U2SMR2
U2SMR3
SDA output disable bit
Start/stop condition
control bit
I C mode select bit 2
Clock-synchronous bit
SCL wait output bit
UART2 initialization bit
SDA digital delay setup
bit
(Note 1, Note 2, Note 3,
SDA output stop bit
SCL wait output bit 2
2
Note 4)
2
2
Bit name
Bit name
Address
Address
0376
0375
16
16
b7 b6 b5
Refer to Table 1.16.11
0 : Disabled
1 : Enabled
0 : Disabled
1 : Enabled
0 : Disabled
1 : Enabled
0: UART2 clock
1: 0 output
0: Enabled
1: Disabled (high impedance)
0 : Disabled
1 : Enabled
Set this bit to “1” in I
(refer to Table 1.16.12)
0 0 0 : Analog delay is selected
0 0 1 : 1 to 2 cycle(s) of 1/f(X
0 1 0 : 2 to 3 cycles of 1/f(X
0 1 1 : 3 to 4 cycles of 1/f(X
1 0 0 : 4 to 5 cycles of 1/f(X
1 0 1 : 5 to 6 cycles of 1/f(X
1 1 0 : 6 to 7 cycles of 1/f(X
1 1 1 : 7 to 8 cycles of 1/f(X
(However, when SDDS = “1”, the initial value is “00
Indeterminate
When reset
When reset
(I C bus exclusive use register)
00
16
2
16
”. When writing to UART2 special mode
(I 2 C bus exclusive use)
2
C mode
Function
Function
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
IN
IN
IN
IN
IN
IN
IN
)
)
)
)
)
)
)
Digital delay
is selected
M16C / 62A Group
Mitsubishi microcomputers
16
) bit
R
R
16
W
W
”)