PIC16HV785-I/SO Microchip Technology, PIC16HV785-I/SO Datasheet - Page 143

• Manufacturer Part Number: PIC16HV785-I/SO
• Description: IC PIC MCU FLASH 2KX14 20SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16HV785-I/SO

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Controller Family/series: PIC16HV
• No. Of I/o's: 18
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• Processor Series: PIC16H
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: RS- 232, USB
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 14 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SO1-1 - SOCKET TRANS ICE 20DIP TO 20SOICAC162060 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Details

19.0
Absolute Maximum Ratings
Ambient temperature under bias................................................................................................................. -40 to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on V
Voltage on MCLR with respect to Vss ........................................................................................................-0.3 to +13.5V
Voltage on RB6 open-drain pin with respect to Vss .....................................................................................-0.3 to +8.5V
Voltage on all other pins with respect to V
Total power dissipation
Total power dissipation
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB, and PORTC (combined) .................................................................200 mA
Maximum current sourced PORTA, PORTB, and PORTC (combined).................................................................200 mA
Note 1:
© 2006 Microchip Technology Inc.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
Note:
ELECTRICAL SPECIFICATIONS
Power dissipation is calculated as follows: P
Voltage spikes below V
Thus, a series resistor of 50-100 should be used when applying a “low” level to the MCLR pin, rather than
pulling this pin directly to V
DD
with respect to V
IK
(1)
(1)
OK
(V
DD
(PDIP and SOIC).........................................................................................................800 mW
(SSOP) ........................................................................................................................600 mW
I
SS
(Vo < 0 or Vo >V
< 0 or V
pin ..............................................................................................................................250 mA
pin ...........................................................................................................................300 mA
(†)
SS
I
SS
> V
............................................................................................................ -0.3 to +6.5V
SS
at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.
DD
.
SS
)
DD
................................................................................. -0.3V to (V
)
Preliminary
DIS
= V
DD
x {I
DD
– ∑ I
PIC16F785/HV785
OH
} + ∑ {(V
DD
– V
OH
) x I
DS41249D-page 141
OH
} + ∑(V
DD
O
+ 0.3V)
l x I
20 mA
20 mA
OL
).