PIC16F723-I/ML Microchip Technology, PIC16F723-I/ML Datasheet - Page 231

• Manufacturer Part Number: PIC16F723-I/ML
• Description: IC PIC MCU FLASH 4KX14 28-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F723-I/ML

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x8b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 25
• Ram Memory Size: 192Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• No. Of Pwm: RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TABLE 23-4:
© 2007 Microchip Technology Inc.
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C ≤ T
Param
30
31
31A
32
33*
34*
35
36*
37*
Note 1: Instruction cycle period (T
No.
*
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
2: By design.
3: Period of the slower clock.
4: To ensure these voltage tolerances, V
5: Design Target. If unable to meet this target, the maximum can be increased, but the minimum cannot be
T
T
T
T
T
T
V
V
T
OST
These parameters are characterized but not tested.
and are not tested.
based on characterization data for that particular oscillator type under standard operating conditions with the
device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption. All devices are tested to operate at “min” values with an external
clock applied to the OSC1 pin. When an external clock input is used, the “max” cycle time limit is “DC” (no
clock) for all devices.
possible. 0.1 μF and 0.01 μF values in parallel are recommended.
changed.
WDT
WDTLP
IOZ
MC
PWRT
BORDC
BOR
HYST
Sym
L
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER,
AND BROWN-OUT RESET PARAMETERS
MCLR Pulse Width (low)
Standard Watchdog Timer Time-out
Period (No Prescaler)
Low Power Watchdog Timer
Time-out Period (No Prescaler)
Oscillator Start-up Timer Period
Power-up Timer Period, PWRTE = 0
I/O high-impedance from MCLR Low
or Watchdog Timer Reset
Brown-out Reset Voltage
Brown-out Reset Hysteresis
Brown-out Reset DC Response
Time
Characteristic
A
CY
≤ +125°C
) equals four times the input oscillator time base period. All specified values are
(5)
DD
(1), (2)
and V
Preliminary
PIC16F72X/PIC16LF72X
SS
2.40
1.80
Min
10
10
10
10
40
25
—
—
2
5
1
must be capacitively decoupled as close to the device as
Typ†
1024
2.5
1.9
17
17
18
18
65
50
—
—
—
3
Max Units
2.60
2.00
140
100
2.0
27
30
27
33
75
10
—
—
—
5
Tosc (Note 3)
mV
ms
ms
ms
ms
ms
μs
μs
μs
μs
V
V
V
V
V
V
V
BORV=2.5V
BORV=1.9V
V
V
-40°C to +85°C
-40°C to 125°C
DD
DD
DD
DD
DD
DD
DD
DD
= 3.3-5V, -40°C to +85°C
= 3.3-5V
= 3.3V-5V, -40°C to +85°C
= 3.3V-5V
= 3.3V-5V, -40°C to +85°C
= 3.3V-5V
≤ V
≤ V
BOR
BOR
Conditions
, -40°C to +85°C
DS41341A-page 229