ATMEGA32U2-MUR Atmel, ATMEGA32U2-MUR Datasheet - Page 31

• Manufacturer Part Number: ATMEGA32U2-MUR
• Description: MCU AVR 32K FLASH 16MHZ 32VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32U2-MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -

7799D–AVR–11/10
The CKSEL0 Fuse together with the SUT1..0 Fuses select the start-up times as shown in
8-4.
Table 8-4.
Notes:
Table 8-5.
Note:
Oscillator Source /
Power Conditions
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Crystal Oscillator, BOD
enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator, slowly
rising power
Power Conditions
BOD enabled
Fast rising power
Slowly rising power
3. If 8 MHz frequency exceeds the specification of the device (depends on V
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
1.
The device is shipped with this option selected.
Fuse can be programmed in order to divide the internal frequency by 8. It must be ensured
that the resulting divided clock meets the frequency specification of the device.
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
Start-up Times for the Low Power Crystal Oscillator Clock Selection
Start-up times for the internal calibrated RC Oscillator clock selection
Start-up Time from
Start-up Time from Power-
Power-down and
down and Power-save
Power-save
16K CK
16K CK
16K CK
258 CK
258 CK
1K CK
1K CK
1K CK
Reserved
6 CK
6 CK
6 CK
ATmega8U2/16U2/32U2
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
14CK + 65 ms
14CK + 65 ms
14CK + 4.1 ms
14CK + 65 ms
(V
from Reset
CC
14CK
14CK
= 5.0V)
Additional Delay from
Reset (V
(2)
14CK + 65 ms
14CK + 4.1 ms
(1)
(2)
(1)
(2)
14CK
CC
= 5.0V)
CKSEL0
(1)
CC
0
0
0
0
1
1
1
1
), the CKDIV8
SUT1..0
SUT1..0
00
01
10
00
01
10
00
01
10
11
11
11
Table
31