ATTINY261-20SU Atmel, ATTINY261-20SU Datasheet - Page 79

• Manufacturer Part Number: ATTINY261-20SU
• Description: IC MCU AVR 2K FLASH 20MHZ 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY261-20SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 55 C
• On-chip Adc: 10 bit, 11 Channel
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.7.4
11.7.5
11.8
2588E–AVR–08/10
Timer/Counter Timing Diagrams
8-bit Input Capture Mode
16-bit Input Capture Mode
cases to consider in the Normal mode, a new counter value can be written anytime. The Output
Compare Unit can be used to generate interrupts at some given time.
The Timer/Counter0 can also be used in an 8-bit Input Capture mode, see
77
The Timer/Counter0 can also be used in a 16-bit Input Capture mode, see
77
The Timer/Counter is a synchronous design and the timer clock (clk
clock enable signal in the following figures. The figures include information on when Interrupt
Flags are set.
shows the count sequence close to the MAX value.
Figure 11-7. Timer/Counter Timing Diagram, no Prescaling
Figure 11-8
Figure 11-8. Timer/Counter Timing Diagram, with Prescaler (f
Figure 11-9 on page 80
TCNTn
(clk
TCNTn
(clk
TOVn
TOVn
clk
clk
clk
clk
for bit settings. For full description, see the section
for bit settings. For full description, see the section
I/O
I/O
I/O
Tn
I/O
Tn
/1)
/8)
shows the same timing data, but with the prescaler enabled.
Figure 11-7
MAX - 1
MAX - 1
shows the setting of OCF0A and OCF0B in Normal mode.
contains timing data for basic Timer/Counter operation. The figure
MAX
MAX
“Input Capture Unit” on page
“Input Capture Unit” on page
clk_I/O
BOTTOM
BOTTOM
/8)
T0
) is therefore shown as a
Table 11-3 on page
Table 11-3 on page
BOTTOM + 1
BOTTOM + 1
75.
75.
79