PIC18F67J11T-I/PT Microchip Technology, PIC18F67J11T-I/PT Datasheet - Page 30

• Manufacturer Part Number: PIC18F67J11T-I/PT
• Description: IC PIC MCU FLASH 64KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F67J11T-I/PT

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Type: FLASH
• Ram Size: 3930 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Ram Memory Size: 3930Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• No. Of Pwm: RoHS Compliant
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3904 B
• Interface Type: EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 68
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183022, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 15 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162091 - HEADER MPLAB ICD2 18F87J11 64/80MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18F67J11T-I/PTTR

PIC18F87J10
TABLE 2-2:
DS39663D-page 28
Osc Type
Capacitor values are for design guidance only.
These capacitors were tested with the crystals listed
below for basic start-up and operation. These values
are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following this table for additional
information.
DD
Note 1: Higher capacitance increases the stability
HS
and temperature range for the application.
2: Since each resonator/crystal has its own
3: Rs may be required to avoid overdriving
4: Always verify oscillator performance over
of oscillator but also increases the
start-up time.
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
components.
crystals with low drive level specification.
the V
expected for the application.
20 MHz
Crystal
4 MHz
8 MHz
Freq.
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
DD
Crystals Used:
and temperature range that is
20 MHz
4 MHz
8 MHz
Typical Capacitor Values
values
27 pF
22 pF
15 pF
C1
Tested:
of
27 pF
22 pF
15 pF
external
C2
Preliminary
2.3
The EC and ECPLL Oscillator modes require an exter-
nal clock source to be connected to the OSC1 pin.
There is no oscillator start-up time required after a
Power-on Reset or after an exit from Sleep mode.
In the EC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 2-2 shows the pin connections for the EC
Oscillator mode.
FIGURE 2-2:
An external clock source may also be connected to the
OSC1 pin in the HS mode, as shown in Figure 2-3. In
this configuration, the divide-by-4 output on OSC2 is
not available.
FIGURE 2-3:
Clock from
Ext. System
Clock from
Ext. System
External Clock Input (EC Modes)
F
Open
OSC
/4
EXTERNAL CLOCK
INPUT OPERATION
(EC CONFIGURATION)
EXTERNAL CLOCK INPUT
OPERATION (HS OSC
CONFIGURATION)
© 2006 Microchip Technology Inc.
OSC1/CLKI
OSC2/CLKO
OSC1
OSC2
PIC18F87J10
PIC18F87J10
(HS Mode)