ATMEGA165PV-8MUR Atmel, ATMEGA165PV-8MUR Datasheet - Page 83

• Manufacturer Part Number: ATMEGA165PV-8MUR
• Description: MCU AVR 16KB FLASH 8MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA165PV-8MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, USART, USI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.2.2
13.3
13.4
8019K–AVR–11/10
Timer/Counter Clock Sources
Counter Unit
Definitions
The double buffered Output Compare Register (OCR0A) is compared with the Timer/Counter
value at all times. The result of the compare can be used by the Waveform Generator to gener-
ate a PWM or variable frequency output on the Output Compare pin (OC0A).
Compare Unit” on page 84.
(OCF0A) which can be used to generate an Output Compare interrupt request.
Many register and bit references in this section are written in general form. A lower case “n”
replaces the Timer/Counter number, in this case 0. A lower case “x” replaces the Output Com-
pare unit number, in this case unit A. However, when using the register or bit defines in a
program, the precise form must be used, that is, TCNT0 for accessing Timer/Counter0 counter
value and so on.
The definitions in
Table 13-1.
The Timer/Counter can be clocked by an internal or an external clock source. The clock source
is selected by the Clock Select logic which is controlled by the Clock Select (CS02:0) bits
located in the Timer/Counter Control Register (TCCR0A). For details on clock sources and pres-
caler, see
The main part of the 8-bit Timer/Counter is the programmable bi-directional counter unit.
13-2
Figure 13-2. Counter Unit Block Diagram
BOTTOM
MAX
TOP
shows a block diagram of the counter and its surroundings.
DATA BUS
“Timer/Counter0 and Timer/Counter1 Prescalers” on page
TCNTn
Timer/Counter Definitions
The counter reaches the BOTTOM when it becomes 0x00.
The counter reaches its MAXimum when it becomes 0xFF (decimal 255).
The counter reaches the TOP when it becomes equal to the highest value in the
count sequence. The TOP value can be assigned to be the fixed value 0xFF
(MAX) or the value stored in the OCR0A Register. The assignment is dependent
on the mode of operation.
Table 13-1
for details. The compare match event will also set the Compare Flag
are also used extensively throughout the document.
direction
count
clear
bottom
Control Logic
top
TOVn
(Int.Req.)
clk
Tn
Clock Select
126.
( From Prescaler )
Detector
ATmega165P
Edge
See “Output
Figure
Tn
83