ATMEGA8515-16JU Atmel, ATMEGA8515-16JU Datasheet - Page 171
![IC MCU AVR 8K 16MHZ IND 44-PLCC](/photos/6/70/67043/453-44-plcc_sml.jpg)
ATMEGA8515-16JU
Manufacturer Part Number
ATMEGA8515-16JU
Description
IC MCU AVR 8K 16MHZ IND 44-PLCC
Manufacturer
Atmel
Series
AVR® ATmegar
Specifications of ATMEGA8515-16JU
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
EBI/EMI, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
35
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Package
44PLCC
Device Core
AVR
Family Name
ATmega
Maximum Speed
16 MHz
Operating Supply Voltage
5 V
Data Bus Width
8 Bit
Number Of Programmable I/os
35
Interface Type
SPI/USART
Number Of Timers
2
Processor Series
ATMEGA8x
Core
AVR8
Data Ram Size
512 B
Maximum Clock Frequency
16 MHz
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
Cpu Family
ATmega
Device Core Size
8b
Frequency (max)
16MHz
Total Internal Ram Size
512Byte
# I/os (max)
35
Number Of Timers - General Purpose
2
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
4.5V
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
44
Package Type
PLCC
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Addressing the Flash
During Self-
Programming
2512K–AVR–01/10
the Z-pointer. The data in R1 and R0 are ignored. The PGERS bit will auto-clear upon
completion of a Page Erase, or if no SPM instruction is executed within four clock
cycles. The CPU is halted during the entire page write operation if the NRWW section is
addressed.
• Bit 0 – SPMEN: Store Program memory Enable
This bit enables the SPM instruction for the next four clock cycles. If written to one
together with either RWWSRE, BLBSET, PGWRT’ or PGERS, the following SPM
instruction will have a special meaning, see description above. If only SPMEN is written,
the following SPM instruction will store the value in R1:R0 in the temporary page buffer
addressed by the Z-pointer. The LSB of the Z-pointer is ignored. The SPMEN bit will
auto-clear upon completion of an SPM instruction, or if no SPM instruction is executed
within four clock cycles. During Page Erase and Page Write, the SPMEN bit remains
high until the operation is completed.
Writing any other combination than “10001”, “01001”, “00101”, “00011”, or “00001” in
the lower five bits will have no effect.
The Z-pointer is used to address the SPM commands.
Since the Flash is organized in pages (see Table 89 on page 183), the Program Counter
can be treated as having two different sections. One section, consisting of the least sig-
nificant bits, is addressing the words within a page, while the most significant bits are
addressing the pages. This is shown in Figure 74. Note that the Page Erase and Page
Write operations are addressed independently. Therefore it is of major importance that
the Boot Loader software addresses the same page in both the Page Erase and Page
Write operation. Once a programming operation is initiated, the address is latched and
the Z-pointer can be used for other operations.
The only SPM operation that does not use the Z-pointer is Setting the Boot Loader Lock
bits. The content of the Z-pointer is ignored and will have no effect on the operation. The
LPM instruction does also use the Z-pointer to store the address. Since this instruction
addresses the Flash byte by byte, also the LSB (bit Z0) of the Z-pointer is used.
Bit
ZH (R31)
ZL (R30)
Z15
15
Z7
7
Z14
14
Z6
6
Z13
Z5
13
5
Z12
12
Z4
4
Z11
11
Z3
3
Z10
ATmega8515(L)
10
Z2
2
Z9
Z1
9
1
Z8
Z0
8
0
171