ATMEGA8515-16JU Atmel, ATMEGA8515-16JU Datasheet - Page 194
![IC MCU AVR 8K 16MHZ IND 44-PLCC](/photos/6/70/67043/453-44-plcc_sml.jpg)
ATMEGA8515-16JU
Manufacturer Part Number
ATMEGA8515-16JU
Description
IC MCU AVR 8K 16MHZ IND 44-PLCC
Manufacturer
Atmel
Series
AVR® ATmegar
Specifications of ATMEGA8515-16JU
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
EBI/EMI, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
35
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Package
44PLCC
Device Core
AVR
Family Name
ATmega
Maximum Speed
16 MHz
Operating Supply Voltage
5 V
Data Bus Width
8 Bit
Number Of Programmable I/os
35
Interface Type
SPI/USART
Number Of Timers
2
Processor Series
ATMEGA8x
Core
AVR8
Data Ram Size
512 B
Maximum Clock Frequency
16 MHz
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
Cpu Family
ATmega
Device Core Size
8b
Frequency (max)
16MHz
Total Internal Ram Size
512Byte
# I/os (max)
35
Number Of Timers - General Purpose
2
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
4.5V
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
44
Package Type
PLCC
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Serial Programming
Algorithm
Data Polling Flash
194
ATmega8515(L)
When writing serial data to the ATmega8515, data is clocked on the rising edge of SCK.
When reading data from the ATmega8515, data is clocked on the falling edge of SCK.
See Figure 85 for timing details.
To program and verify the ATmega8515 in the Serial Programming mode, the following
sequence is recommended (See four byte instruction formats in Table 94.):
1. Power-up sequence:
2. Wait for at least 20 ms and enable serial programming by sending the Program-
3. The Serial Programming instructions will not work if the communication is out of
4. The Flash is programmed one page at a time. The page size is found in Table 89
5. The EEPROM array is programmed one byte at a time by supplying the address
6. Any memory location can be verified by using the Read instruction which returns
7. At the end of the programming session, RESET can be set high to commence
8. Power-off sequence (if needed):
When a page is being programmed into the Flash, reading an address location within
the page being programmed will give the value $FF. At the time the device is ready for a
new page, the programmed value will read correctly. This is used to determine when the
next page can be written. Note that the entire page is written simultaneously and any
address within the page can be used for polling. Data polling of the Flash will not work
for the value $FF, so when programming this value, the user will have to wait for at least
t
all locations, programming of addresses that are meant to contain $FF, can be skipped.
See Table 93 for t
WD_FLASH
Apply power between V
some systems, the programmer can not guarantee that SCK is held low during
Power-up. In this case, RESET must be given a positive pulse of at least two
CPU clock cycles duration after SCK has been set to “0”.
ming Enable serial instruction to pin MOSI.
synchronization. When in synchronization, the second byte ($53), will echo back
when issuing the third byte of the Programming Enable instruction. Whether the
echo is correct or not, all four bytes of the instruction must be transmitted. If the
$53 did not echo back, give RESET a positive pulse and issue a new Program-
ming Enable command.
on page 183. The memory page is loaded one byte at a time by supplying the 5
LSB of the address and data together with the Load Program memory Page
instruction. To ensure correct loading of the page, the data low byte must be
loaded before data high byte is applied for a given address. The Program mem-
ory Page is stored by loading the Write Program memory Page instruction with
the 7 MSB of the address. If polling is not used, the user must wait at least
t
gramming interface before the Flash write operation completes can result in
incorrect programming.
and data together with the appropriate Write instruction. An EEPROM memory
location is first automatically erased before new data is written. If polling is not
used, the user must wait at least t
Table 93. In a chip erased device, no $FFs in the data file(s) need to be
programmed.
the content at the selected address at serial output MISO.
normal operation.
Set RESET to “1”.
Turn V
WD_FLASH
before programming the next page. As a chip erased device contains $FF in
CC
power off.
before issuing the next page, see Table 93. Accessing the serial pro-
WD_FLASH
value.
CC
and GND while RESET and SCK are set to “0”. In
WD_EEPROM
before issuing the next byte, see
2512K–AVR–01/10